參數資料
型號： AD9737A-EBZ
廠商： Analog Devices Inc
文件頁數： 58/64頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR AD9737A
標準包裝： 1
系列： *
Data Sheet
AD9737A/AD9739A
Rev. | Page 61 of 64
LAB EVALUATION OF THE AD9737A/AD9739A
Figure 187 shows a recommended lab setup that was used to
characterize the performance of the AD9737A/AD9739A. The
DPG2 is a dual port LVDS/CMOS data pattern generator that is
available from Analog Devices, Inc., with an up to 1.25 GSPS
data rate. The DPG2 directly interfaces to the AD9737A/AD9739A
evaluation board via Tyco Z-PACK HM-Zd connectors. A low
phase noise/jitter RF source such as an R&S SMA100A signal
generator is used for the DAC clock. A +5 V power supply is
used to power up the AD9737A/AD9739A evaluation board,
and SMA cabling is used to interface to the supply, clock source,
and spectrum analyzer. A USB 2.0 interface to a host PC is used
to communicate to both the AD9737A/AD9739A evaluation
board and the DPG2.
A high dynamic range spectrum analyzer is required to evaluate
the ac performance of the AD9737A/AD9739A reconstructed
waveform. This is especially the case when measuring ACLR
performance for high dynamic range applications such as
multicarrier DOCSIS CMTS applications. Harmonic, SFDR,
and IMD measurements pertaining to unmodulated carriers
can benefit by using a sufficiently high RF attenuation setting
because these artifacts are easy to identify above the spectrum
analyzer noise floor. However, reconstructed waveforms having
modulated carrier(s) often benefit from the use of a high dynamic
range RF amplifier and/or passive filters to measure close-in
and wideband ACLR performance when using spectrum
analyzers of limited dynamic range.
ADI PATTERN GENERATOR
DPG2
AD9739
EVAL. BOARD
RHODE AND
SCHWARTZ
SMA 100A
AGILENT PSA
E4440A
10 MHz
REFIN
10 MHz
REOUT
LAB
PC
USB 2.0
GPIB
LVDS
DATA
AND DCI
DCO
1.6GHz TO
2.5GHz
3dBm
POWER
SUPPLY
+5V
09616-
106
Figure 187. Lab Test Setup Used to Characterize the AD9737A/AD9739A
RECOMMENDED START-UP SEQUENCE
On power-up of the AD9737A/AD9739A, a host processor is
required to initialize and configure the AD9737A/AD9739A
via its SPI port. Figure 188 shows a flowchart of the sequential
steps required. Table 29 provides more detail on the SPI register
write/read operations required to implement the flowchart
steps. Note the following:
A software reset is optional because the AD9737A/AD9739A
have both an internal POR circuit and a RESET pin.
The Mu controller must be first enabled (and in track mode)
before the data receiver controller is enabled because the DCO
output signal is derived from this circuitry.
A wait period is related to fDATA periods.
Limit the number of attempts to lock the controllers to three;
locks typically occur on the first attempt.
Hardware or software interrupts can be used to monitor the
status of the controllers.
CONFIGURE
SPI PORT
SOFTWARE
RESET
SET CLK
INPUT CMV
CONFIGURE
MU CONT.
WAIT A
FEW 100s
MU CONT.
LOCKED?
YES
NO
YES
WAIT A
FEW 100s
NO
RECONFIGURE
TXDAC FROM
DEFAULT SETTING
OPTIONAL
CONFIGURE
RX DATA
CONT.
RX DATA
CONT.
LOCKED?
09616-
107
Figure 188. Flowchart for Initialization and Configuration of the
C
相關PDF資料
PDF描述
MIC2026-1YM IC DISTRIBUTION SW DUAL 8-SOIC
VI-B1L-EY CONVERTER MOD DC/DC 28V 50W
AD9706-DPG2-EBZ BOARD EVAL FOR AD9706
AD9705-DPG2-EBZ BOARD EVAL FOR AD9705
MIC2026-2YM IC DISTRIBUTION SW DUAL 8-SOIC
相關代理商/技術參數
參數描述
AD9739 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit, 2.5 GSPS, RF Digital-to-Analog Converter
AD9739A 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit, 2.5 GSPS, RF Digital-to-Analog Converter
AD9739ABBC 制造商:Analog Devices 功能描述:14 BIT 2.5 GSPS DAC A REVISION - Trays
AD9739ABBCRL 制造商:Analog Devices 功能描述:14 BIT 2.5 GSPS DAC A REVISION - Tape and Reel
AD9739ABBCZ 功能描述:數模轉換器- DAC 14 Bit 2.5 GSPS DAC A Revision RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*