參數資料
型號： AD9649BCPZRL7-80
廠商： Analog Devices Inc
文件頁數： 14/32頁
文件大小： 0K
描述： IC ADC 14BIT 80MSPS 32LFCSP
標準包裝： 1,500
位數： 14
采樣率（每秒）： 80M
數據接口： 串行，SPI?
轉換器數目： 1
功率耗散（最大）： 100mW
電壓電源： 模擬和數字
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 32-VFQFN 裸露焊盤，CSP
供應商設備封裝： 32-LFCSP-VQ
包裝： 帶卷 (TR)
輸入數目和類型： 2 個單端，單極；1 個差分，單極
AD9649
Rev. 0 | Page 21 of
32
Clock Duty Cycle
Typical high speed ADCs use both clock edges to generate a
variety of internal timing signals and, as a result, may be sensitive
to clock duty cycle. Commonly, a 50% duty cycle clock with ±5%
tolerance is required to maintain optimum dynamic performance,
as shown in Figure 52.
Jitter on the rising edge of the clock input can also impact dynamic
performance and should be minimized, as discussed in the Jitter
Considerations section of this datasheet.
80
75
70
65
60
55
50
40
45
10
20
30
40
50
60
70
80
POSITIVE DUTY CYCLE (%)
S
N
R
(
d
BF
S
)
0
85
39
-0
53
Figure 52. SNR vs. Clock Duty Cycle
Jitter Considerations
High speed, high resolution ADCs are sensitive to the quality
of the clock input. The degradation in SNR from the low fre-
quency SNR (SNRLF) at a given input frequency (fINPUT) due to
jitter (tJRMS) can be calculated by
SNRHF = 10 log[(2π × fINPUT × tJRMS)2 + 10
]
)
10
/
(
LF
SNR
In the previous equation, the rms aperture jitter represents the
clock input jitter specification. IF undersampling applications
are particularly sensitive to jitter, as illustrated in Figure 53.
80
75
70
65
60
55
50
45
1
10
100
1k
FREQUENCY (MHz)
S
NR
(
d
BF
S
)
0.5ps
0.2ps
0.05ps
1.0ps
1.5ps
2.0ps
2.5ps
3.0ps
0
853
9-
0
22
Figure 53. SNR vs. Input Frequency and Jitter
The clock input should be treated as an analog signal in cases in
which aperture jitter may affect the dynamic range of the AD9649.
To avoid modulating the clock signal with digital noise, keep power
supplies for clock drivers separate from the ADC output driver
supplies. Low jitter, crystal-controlled oscillators make the best
clock sources. If the clock is generated from another type of source
(by gating, dividing, or another method), it should be retimed by
the original clock at the last step.
For more information, see the AN-501 Application Note and the
AN-756 Application Note, which are available on www.analog.com.
POWER DISSIPATION AND STANDBY MODE
As shown in Figure 54, the analog core power dissipated by the
AD9649 is proportional to its sample rate. The digital power dis-
sipation of the CMOS outputs are determined primarily by the
strength of the digital drivers and the load on each output bit.
The maximum DRVDD current (IDRVDD) can be calculated as
IDRVDD = VDRVDD × CLOAD × fCLK × N
where N is the number of output bits (15, in the case of the
AD9649).
This maximum current occurs when every output bit switches
on every clock cycle, that is, a full-scale square wave at the Nyquist
frequency of fCLK/2. In practice, the DRVDD current is estab-
lished by the average number of output bits that are switching,
which is determined by the sample rate and the characteristics
of the analog input signal.
Reducing the capacitive load presented to the output drivers can
minimize digital power consumption. The data in Figure 54 was
taken using the same operating conditions as those used for the
output driver.
85
75
65
55
80
70
60
50
45
35
40
10
20
30
40
50
60
70
80
CLOCK RATE (MSPS)
ANAL
O
G
C
O
RE
P
O
W
E
R
(
m
W
)
AD9649-80
AD9649-65
AD9649-40
AD9649-20
08
53
9-
05
1
Figure 54. Analog Core Power vs. Clock Rate
In SPI mode, the AD9649 can be placed in power-down mode
directly via the SPI port or by using the programmable external
MODE pin. In non-SPI mode, power-down is achieved by assert-
ing the PDWN pin high. In this state, the ADC typically dissipates
500 μW. During power-down, the output drivers are placed in a
high impedance state. Asserting the PDWN pin (or the MODE pin
in SPI mode) low returns the AD9649 to normal operating mode.
Note that PDWN is referenced to the digital output driver supply
(DRVDD) and should not exceed that supply voltage.
相關PDF資料
PDF描述
AD9653BCPZRL7-125 IC ADC 16BIT 125MSPS SRL 48LFCSP
AD9707BCPZRL7 IC DAC TX 14BIT 175MSPS 32-LFCSP
AD9709ASTZRL IC DAC 8BIT DUAL 125MSPS 48LQFP
AD9715BCPZ IC DAC DUAL 10BIT LO PWR 40LFCSP
AD9726BSVZRL IC DAC 16IT LVDS 400MSPS 80-TQFP
相關代理商/技術參數
參數描述
AD9649W 功能描述:IC ADC 制造商:analog devices inc. 系列:* 零件狀態:上次購買時間 標準包裝:1
AD9649XCPZ-80 功能描述:14 Bit Analog to Digital Converter 1 Input 1 Pipelined 32-LFCSP-WQ (5x5) 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:上次購買時間 位數:14 采樣率（每秒）:80M 輸入數:1 輸入類型:差分 數據接口:并聯 配置:S/H-ADC 無線電 - S/H:ADC:1:1 A/D 轉換器數:1 架構:管線 參考類型:內部 電壓 - 電源，模擬:1.7 V ~ 1.9 V 電壓 - 電源，數字:1.7 V ~ 3.6 V 特性:- 工作溫度:-40°C ~ 85°C 封裝/外殼:32-VFQFN 裸露焊盤，CSP 供應商器件封裝:32-LFCSP-WQ（5x5） 標準包裝:1
AD9650 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 25 MSPS/65 MSPS/80 MSPS/105 MSPS, 1.8 V Dual Analog-to-Digital Converter (ADC)
AD9650-105EBZ 功能描述:數據轉換 IC 開發工具 16Bit Hi SNR 105 Msps Dual ADC RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
AD9650-25EBZ 功能描述:數據轉換 IC 開發工具 16Bit Hi SNR 25 Msps Dual ADC RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*