參數資料
型號: AD9279-80KITZ
廠商: Analog Devices Inc
文件頁數: 18/44頁
文件大?。?/td> 0K
描述: KIT EVALUATION FOR AD9279
標準包裝: 1
ADC 的數量: 8
位數: 12
采樣率(每秒): 80M
數據接口: 串行
工作溫度: -40°C ~ 85°C
已用 IC / 零件: AD9279
已供物品:
AD9279
Rev. 0 | Page 25 of 44
The main purpose of input impedance matching is to improve the
transient response of the system. With shunt termination, the input
noise increases due to the thermal noise of the matching resistor
and the increased contribution of the LNA input voltage noise
generator. With active termination, however, the contributions
of both are smaller (by a factor of 1/(1 + LNA Gain)) than they
would be for shunt termination.
Figure 48 shows the relative noise figure performance. With an
LNA gain of 21.3 dB, the input impedance was swept with RS to
preserve the match at each point. The noise figures for a source
impedance of 50 Ω are 7.3 dB, 4.2 dB, and 2.8 dB for the shunt
termination, active termination, and unterminated configurations,
respectively. The noise figures for 200 Ω are 4.5 dB, 1.7 dB, and
1.0 dB, respectively.
Figure 49 shows the noise figure as it relates to RS for various
values of RIN, which is helpful for design purposes.
10
100
1k
0
1.5
3.0
4.5
6.0
7.5
9.0
10.5
12.0
RS ()
NO
IS
E
F
IG
U
RE
(
d
B)
UNTERMINATED
ACTIVE TERMINATION
09
42
3-
0
42
SHUNT TERMINATION
Figure 48. Noise Figure vs. RS for Shunt Termination, Active
Termination Matched and Unterminated Inputs, VGAIN = 1.6 V
10
100
1k
0
1
2
3
4
5
6
7
8
RS ()
NO
IS
E
F
IG
U
RE
(
d
B)
RIN = 50
RIN = 75
RIN = 100
RIN = 200
UNTERMINATED
09
42
3-
0
43
Figure 49. Noise Figure vs. RS for Various Fixed Values of RIN,
Active Termination Matched Inputs, VGAIN = 1.6 V
Input Overdrive
Excellent overload behavior is of primary importance in
ultrasound. Both the LNA and VGA have built-in overdrive
protection and quickly recover after an overload event.
As with any amplifier, voltage clamping prior to the inputs
is highly recommended if the application is subject to high
transient voltages.
Figure 50 shows a simplified ultrasound transducer interface.
A common transducer element serves the dual functions of
transmitting and receiving ultrasound energy. During the
transmitting phase, high voltage pulses are applied to the ceramic
elements. A typical transmit/receive (T/R) switch can consist of
four high voltage diodes in a bridge configuration. Although the
diodes ideally block transmit pulses from the sensitive receiver
input, diode characteristics are not ideal, and the resulting leakage
transients imposed on the LI-x inputs can be problematic.
The external input overload protection scheme also contains a
pair of back-to-back signal diodes that should be in place prior to
the ac coupling capacitors. Keep in mind that all diodes are prone
to exhibiting some amount of shot noise. Many types of diodes are
available for achieving the desired noise performance. The
configuration shown in Figure 50 tends to add 2 nV/√Hz of
input-referred noise. Decreasing the 5 kΩ resistor and increasing
the 2 kΩ resistor may improve noise contribution, depending on
the application. With the diodes shown in Figure 50, clamping
levels of ±0.5 V or less significantly enhance the overload
performance of the system.
Because ultrasound is a pulse system and time-of-flight is used
to determine depth, quick recovery from input overloads is
essential. Overload can occur in the preamplifier and in the
VGA. Immediately following a transmit pulse, the typical VGA
gains are low, and the LNA is subject to overload from T/R
switch leakage. With increasing gain, the VGA can become
overloaded due to strong echoes that occur near field echoes
and acoustically dense materials, such as bone.
TRANSDUCER
10nF
2k
5k
5k
AD9279
Tx
DRIVER
HV
+5V
–5V
LNA
09
42
3-
04
4
Figure 50. Input Overload Protection
相關PDF資料
PDF描述
VI-BWZ-EW CONVERTER MOD DC/DC 2V 40W
UVZ1V103MRD CAP ALUM 10000UF 35V 20% RADIAL
VI-BWY-EY CONVERTER MOD DC/DC 3.3V 33W
AD9641-80KITZ BOARD EVAL FOR AD9641
LGU2C102MELB CAP ALUM 1000UF 160V 20% SNAP
相關代理商/技術參數
參數描述
AD9279BBCZ 功能描述:IC ADC 12BIT 80MSPS 144CSPBGA RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤
AD9279-BBCZ 制造商:AD 制造商全稱:Analog Devices 功能描述:Octal LNA/VGA/AAF/ADC and CW I/Q Demodulator
AD9280 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete 8-Bit, 32 MSPS, 95 mW CMOS A/D Converter
AD9280ARS 功能描述:IC ADC CMOS 8BIT 32MSPS 28-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率(每秒):3M 數據接口:- 轉換器數目:- 功率耗散(最大):- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:-
AD9280ARSRL 功能描述:IC ADC 8BIT CMOS 32MSPS 28-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率(每秒):3M 數據接口:- 轉換器數目:- 功率耗散(最大):- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:-