- 您現在的位置：買賣IC網 > PDF目錄10511 > AD9253BCPZ-80 (Analog Devices Inc)IC ADC 14BIT SRL 80MSPS 48LFCSP PDF資料下載
參數資料
| 型號： | AD9253BCPZ-80 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 17/40頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT SRL 80MSPS 48LFCSP |
| 標準包裝： | 1 |
| 位數： | 14 |
| 采樣率（每秒）： | 80M |
| 數據接口： | LVDS，串行，SPI? |
| 轉換器數目： | 4 |
| 功率耗散（最大）： | 405mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-WFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 48-LFCSP-WQ（7x7） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 4 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
AD9253
Data Sheet
Rev. 0 | Page 24 of 40
3.0
If the internal reference of the AD9253 is used to drive multiple
converters to improve gain matching, the loading of the reference
by the other converters must be considered. Figure 60 shows
how the internal reference voltage is affected by loading.
0
–0.5
–1.0
–1.5
–2.0
–2.5
–3.0
–3.5
–4.0
–4.5
–5.0
0
2.5
2.0
1.5
1.0
0.5
V
RE
F
E
R
RO
R
(
%
)
LOAD CURRENT (mA)
1006
5-
061
INTERNAL VREF = 1V
Figure 60. VREF Error vs. Load Current
External Reference Operation
The use of an external reference may be necessary to enhance
the gain accuracy of the ADC or improve thermal drift charac-
teristics. Figure 61 shows the typical drift characteristics of the
internal reference in 1.0 V mode.
4
–8
–40
85
V
RE
F
E
RRO
R
(
m
V
)
TEMPERATURE (°C)
10
065
-06
2
–6
–4
–2
0
2
–15
10
35
60
Figure 61. Typical VREF Drift
When the SENSE pin is tied to AVDD, the internal reference is
disabled, allowing the use of an external reference. An internal
reference buffer loads the external reference with an equivalent
7.5 kΩ load (see Figure 54). The internal buffer generates the
positive and negative full-scale references for the ADC core. There-
fore, the external reference must be limited to a maximum of 1.0 V.
It is not recommended to leave the SENSE pin floating.
CLOCK INPUT CONSIDERATIONS
For optimum performance, clock the AD9253 sample clock
inputs, CLK+ and CLK, with a differential signal. The signal
is typically ac-coupled into the CLK+ and CLK pins via a
transformer or capacitors. These pins are biased internally
(see Figure 48) and require no external bias.
Clock Input Options
The AD9253 has a flexible clock input structure. The clock input
can be a CMOS, LVDS, LVPECL, or sine wave signal.
Regardless of the type of signal being used, clock source jitter is
of the most concern, as described in the Jitter Considerations
section.
ing the AD9253 (at clock rates up to 1 GHz prior to internal CLK
divider). A low jitter clock source is converted from a single-
ended signal to a differential signal using either an RF transformer
or an RF balun.
The RF balun configuration is recommended for clock frequencies
between 125 MHz and 1 GHz, and the RF transformer is recom-
mended for clock frequencies from 10 MHz to 200 MHz. The
back-to-back Schottky diodes across the transformer/balun
secondary winding limit clock excursions into the AD9253 to
approximately 0.8 V p-p differential.
This limit helps prevent the large voltage swings of the clock
from feeding through to other portions of the AD9253 while
preserving the fast rise and fall times of the signal that are critical
to achieving low jitter performance. However, the diode
capacitance comes into play at frequencies above 500 MHz. Care
must be taken in choosing the appropriate signal limiting diode.
0.1F
SCHOTTKY
DIODES:
HSMS2822
CLOCK
INPUT
50
100
CLK–
CLK+
ADC
Mini-Circuits
ADT1-1WT, 1:1 Z
XFMR
1
006
5-
06
4
Figure 62. Transformer-Coupled Differential Clock (Up to 200 MHz)
0.1F
CLOCK
INPUT
0.1F
50
CLK–
CLK+
SCHOTTKY
DIODES:
HSMS2822
ADC
1
006
5-
065
Figure 63. Balun-Coupled Differential Clock (Up to 1 GHz)
If a low jitter clock source is not available, another option is to
ac couple a differential PECL signal to the sample clock input
excellent jitter performance.
A third option is to ac couple a differential LVDS signal to the
clock drivers offer excellent jitter performance.
In some applications, it may be acceptable to drive the sample
clock inputs with a single-ended 1.8 V CMOS signal. In such
applications, drive the CLK+ pin directly from a CMOS gate, and
相關PDF資料 |
PDF描述 |
|---|---|
| CS3101A-18-10S | CONN RCPT 4POS IN LINE W/SCKT |
| LTC2261IUJ-12#PBF | IC ADC 12-BIT 125MSPS 40-QFN |
| UP050CH110J-NAC | CAP CER 11PF 50V 5% AXIAL |
| VE-BTX-MX-F4 | CONVERTER MOD DC/DC 5.2V 75W |
| AD9222ABCPZ-50 | IC ADC 12BIT SRL 50MSPS 64LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9253BCPZRL7-105 | 功能描述:模數轉換器 - ADC 14 Bit 105Msps Quad ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9253BCPZRL7-125 | 功能描述:模數轉換器 - ADC 14 Bit 125Msps Quad ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9253BCPZRL7-80 | 功能描述:模數轉換器 - ADC 14 Bit 80 Msps Quad ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9253TCPZ-125EP | 功能描述:IC ADC 14BIT SRL 125MSPS 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 位數:12 采樣率（每秒）:1.8M 數據接口:并聯 轉換器數目:1 功率耗散（最大）:1.82W 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:管件 輸入數目和類型:2 個單端，單極 |
| AD9253TCPZR7-125EP | 制造商:Analog Devices 功能描述:14 BIT 125MSPS QUAD ADC 制造商:Analog Devices 功能描述:14 BIT 125MSPS QUAD ADC - Tape and Reel 制造商:Analog Devices 功能描述:IC ADC 14BIT SRL 125MSPS 48LFCSP 制造商:Analog Devices Inc. 功能描述:Analog to Digital Converters - ADC 14 Bit 125Msps Quad ADC 制造商:Analog Devices 功能描述:CONVERTER - ADC |
發布緊急采購，3分鐘左右您將得到回復。