參數資料
型號: AD8469WBRMZ-RL
廠商: Analog Devices Inc
文件頁數: 11/12頁
文件大?。?/td> 0K
描述: IC COMPARATOR R-R TTL/CMOS 8MSOP
標準包裝: 3,000
類型: 通用
元件數: 1
輸出類型: CMOS,TTL
電壓 - 電源,單路/雙路(±): 2.5 V ~ 5.5 V
電壓 - 輸入偏移(最小值): 3mV @ 2.5V
電流 - 輸入偏壓(最小值): 0.4µA @ 2.5V
電流 - 輸出(標準): 50mA
電流 - 靜態(最大值): 800µA
CMRR, PSRR(標準): 50dB CMRR,50dB PSRR
傳輸延遲(最大): 40ns
磁滯: 100µV
工作溫度: -40°C ~ 125°C
封裝/外殼: 8-TSSOP,8-MSOP(0.118",3.00mm 寬)
安裝類型: 表面貼裝
包裝: 帶卷 (TR)
AD8469
Data Sheet
Rev. 0 | Page 8 of 12
APPLICATIONS INFORMATION
POWER/GROUND LAYOUT AND BYPASSING
The AD8469 comparator is a high speed device. Despite the
low noise output stage, it is essential to use proper high speed
design techniques to achieve the specified performance. Because
comparators are uncompensated amplifiers, feedback in any
phase relationship is likely to cause oscillations or undesired
hysteresis. Of critical importance is the use of low impedance
supply planes, particularly the output supply plane (VCC) and
the ground plane. Separate supply planes are recommended
as part of a multilayer board. Providing the lowest inductance
return path for switching currents ensures the best possible
performance in the target application.
It is also important to adequately bypass the input and output
supplies. Place a 0.1 μF bypass capacitor as close as possible to
each supply pin. The capacitors should be connected to the
ground plane with redundant vias placed to provide a physically
short return path for output currents flowing back from ground
to the VCC pin. Use high frequency bypass capacitors for mini-
mum inductance and effective series resistance (ESR). Parasitic
layout inductance should also be strictly controlled to maximize
the effectiveness of the bypass at high frequencies.
TTL-/CMOS-COMPATIBLE OUTPUT STAGE
To achieve the specified propagation delay performance, keep
the capacitive load at or below the specified maximum value.
The outputs of the AD8469 are designed to directly drive one
Schottky TTL or three low power Schottky TTL loads (or
equivalent). For large fan outputs, buses, or transmission lines,
use an appropriate buffer to maintain the excellent speed and
stability of the comparator.
With the rated 15 pF load capacitance applied, more than half
of the total device propagation delay is output stage slew time.
For this reason, the total propagation delay decreases as VCC
decreases, and instability in the power supply may appear as
excess delay dispersion.
Delay is measured to the 50% point of the supply that is in use;
therefore, the fastest times are observed with the VCC supply at
2.5 V, and larger delay values are observed when driving loads
that switch at other levels.
Overdrive and input slew rate dispersions are not significantly
affected by output loading and VCC variations.
A simplified schematic diagram of the TTL-/CMOS-compatible
output stage is shown in Figure 11. Because of its inherent sym-
metry and generally good behavior, this output stage is readily
adaptable for driving various filters and other unusual loads.
OUTPUT
Q2
Q1
+IN
–IN
OUTPUT STAGE
VLOGIC
GAIN STAGE
A2
A1
AV
1049
0-
01
1
Figure 11. Simplified Schematic Diagram of
TTL-/CMOS-Compatible Output Stage
OPTIMIZING PERFORMANCE
As with any high speed comparator, proper design and layout
techniques are essential to obtain the specified performance. Stray
capacitance, inductance, common power and ground impedances,
or other layout issues can severely limit performance and often
cause oscillation. Source impedance should be minimized as
much as possible. High source impedance, in combination with
the parasitic input capacitance of the comparator, causes an unde-
sirable degradation in bandwidth at the input, therefore degrading
the overall response. Higher impedances encourage undesired
coupling.
COMPARATOR PROPAGATION DELAY DISPERSION
The AD8469 comparator is designed to reduce propagation delay
dispersion over a wide input overdrive range of 10 mV to VCC 1 V.
Propagation delay dispersion is the variation in propagation delay
that results from a change in the degree of overdrive or slew rate—
that is, how far or how fast the input signal exceeds the switching
threshold (see Figure 12 and Figure 13).
The propagation delay dispersion specification becomes important
in high speed, time critical applications, such as data communica-
tion, automatic test and measurement, and instrumentation. It is
also important in event driven applications, such as pulse spectros-
copy, nuclear instrumentation, and medical imaging. Dispersion is
the variation in propagation delay as the input overdrive conditions
are changed (see Figure 12).
The propagation delay dispersion of the AD8469 is typically <12 ns
as the overdrive varies from 10 mV to 125 mV. This specification
applies to both positive and negative signals because the device has
very closely matched delays for both positive-going and negative-
going inputs, and very low output skews. Note that for repeatable
dispersion measurements the actual device offset is added to the
overdrive.
相關PDF資料
PDF描述
AD8561ARU-REEL IC COMP 7NS ULTRA-FAST 8-TSSOP
AD8564ARU-REEL IC COMP QUAD 7NS FAST 16-TSSOP
AD8611ARM-REEL IC COMP SNGL 4NS ULTRFAST 8-MSOP
AD9387NKBBCZRL-80 XMITTER HDMI/DVI LP 76CSPBGA
AD96687BR-REEL IC COMP DUAL 2.5NS 16-SOIC
相關代理商/技術參數
參數描述
AD846AH 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Current-Feedback Operational Amplifier
AD846AN 制造商:Analog Devices 功能描述:OP Amp Single Current Fdbk 制造商:Rochester Electronics LLC 功能描述:450V/US,PRECISION OPAMP - Bulk 制造商:Analog Devices 功能描述:OP AMP CURRENT FEEDBACK DIP8 846
AD846AQ 制造商:AD 制造商全稱:Analog Devices 功能描述:450 V/us, Precision, Current-Feedback Op Amp
AD846AR-16 制造商:AD 制造商全稱:Analog Devices 功能描述:450 V/us, Precision, Current-Feedback Op Amp
AD846AR-16-REEL 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel