- 您現在的位置：買賣IC網 > PDF目錄2063 > AD8468WBKSZ-R7 (Analog Devices Inc)IC COMPARATOR TTL/CMOS SC70-6 PDF資料下載
參數資料
| 型號： | AD8468WBKSZ-R7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC COMPARATOR TTL/CMOS SC70-6 |
| 標準包裝： | 1 |
| 類型： | 通用 |
| 元件數： | 1 |
| 輸出類型： | CMOS，滿擺幅，TTL |
| 電壓 - 電源，單路/雙路(±)： | 2.5 V ~ 5.5 V |
| 電壓 - 輸入偏移（最小值）： | 10mV @ 2.5V |
| 電流 - 輸入偏壓（最小值）： | 0.4µA @ 2.5V |
| 電流 - 輸出（標準）： | 50mA |
| 電流 - 靜態（最大值）： | 1.3mA |
| CMRR, PSRR（標準）： | 45dB CMRR，50dB PSRR |
| 傳輸延遲（最大）： | 60ns |
| 工作溫度： | -40°C ~ 125°C |
| 封裝/外殼： | 6-TSSOP，SC-88，SOT-363 |
| 安裝類型： | 表面貼裝 |
| 包裝： | 標準包裝 |
| 其它名稱： | AD8468WBKSZ-R7DKR |
AD8468
Rev. 0 | Page 7 of 12
APPLICATIONS INFORMATION
POWER/GROUND LAYOUT AND BYPASSING
The AD8468 comparator is a high speed device. Despite
the low noise output stage, it is essential to use proper high
speed design techniques to achieve the specified performance.
Because comparators are uncompensated amplifiers, feedback
in any phase relationship is likely to cause oscillations or
undesired hysteresis. Of critical importance is the use of low
impedance supply planes, particularly the output supply plane
(VCC) and the ground plane (GND). Individual supply planes
are recommended as part of a multilayer board. Providing the
lowest inductance return path for switching currents ensures
the best possible performance in the target application.
It is also important to adequately bypass the input and output
supplies. A 0.1 F bypass capacitor should be placed as close as
possible to the VCC supply pin. The capacitor should be connected
to the GND plane with redundant vias placed to provide a
physically short return path for output currents flowing back
from ground to the VCC pin. High frequency bypass capacitors
should be carefully selected for minimum inductance and ESR.
Parasitic layout inductance should also be strictly controlled to
maximize the effectiveness of the bypass at high frequencies.
TTL-/CMOS-COMPATIBLE OUTPUT STAGE
Specified propagation delay performance can be achieved only
by keeping the capacitive load at or below the specified minimums.
The output of the AD8468 is designed to directly drive one
Schottky TTL, three low power Schottky TTL loads, or the
equivalent. For large fanouts, buses, or transmission lines, use
an appropriate buffer to maintain the excellent speed and
stability of the comparator.
With the rated 15 pF load capacitance applied, more than half
of the total device propagation delay is output stage slew time.
Because of this, the total propagation delay decreases as VCC
decreases, and instability in the power supply may appear as
excess delay dispersion.
Delay is measured to the 50% point for whatever supply is in
use; thus, the fastest times are observed with the VCC supply at
2.5 V, and larger values are observed when driving loads that
switch at other levels.
Overdrive and input slew rate dispersions are not significantly
affected by output loading and VCC variations.
The TTL-/CMOS-compatible output stage is shown in the
simplified schematic diagram (see Figure 9). Because of its
inherent symmetry and generally good behavior, this output
stage is readily adaptable for driving various filters and other
unusual loads.
OUTPUT
Q2
Q1
+IN
–IN
OUTPUT STAGE
VLOGIC
GAIN STAGE
A2
A1
AV
08853-
009
Figure 9. Simplified Schematic Diagram of the
TTL-/CMOS-Compatible Output Stage
OPTIMIZING PERFORMANCE
As with any high speed comparator, proper design and layout
techniques are essential for obtaining the specified performance.
Stray capacitance, inductance, common power and ground
impedances, or other layout issues can severely limit performance
and can often cause oscillation. The source impedance should
be minimized as much as is practicable. High source impedance,
in combination with the parasitic input capacitance of the
comparator, causes an undesirable degradation in bandwidth at
the input, thus degrading the overall response. Higher impedances
encourage undesired coupling.
COMPARATOR PROPAGATION
DELAY DISPERSION
The AD8468 comparator is designed to reduce propagation
delay dispersion over a wide input overdrive range of 10 mV to
VCC – 1 V. Propagation delay dispersion is the variation in
propagation delay that results from a change in the degree of
overdrive or slew rate (how far or how fast the input signal
exceeds the switching threshold). See Figure 10 and Figure 11.
Propagation delay dispersion is a specification that becomes
important in high speed, time-critical applications, such as data
communication, automatic test and measurement, and instru-
mentation. It is also important in event-driven applications, such
as pulse spectroscopy, nuclear instrumentation, and medical
imaging.
AD8468 overdrive dispersion is typically <12 ns as the
overdrive varies from 10 mV to 125 mV. This specification
applies to both positive and negative signals because the device
has very closely matched delays for both positive-going and
negative-going inputs and very low output skews. Remember to
add the actual device offset to the overdrive for repeatable
dispersion measurements.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8469WBRMZ-RL | IC COMPARATOR R-R TTL/CMOS 8MSOP |
| AD8561ARU-REEL | IC COMP 7NS ULTRA-FAST 8-TSSOP |
| AD8564ARU-REEL | IC COMP QUAD 7NS FAST 16-TSSOP |
| AD8611ARM-REEL | IC COMP SNGL 4NS ULTRFAST 8-MSOP |
| AD9387NKBBCZRL-80 | XMITTER HDMI/DVI LP 76CSPBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8468WBKSZ-RL | 功能描述:校驗器 IC R-R InputTTL/CMOSOut Comparitor RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| AD8469 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Fast, Rail-to-Rail, Low Power, 2.5 V to 5.5 V |
| AD8469WBRMZ | 功能描述:IC COMPARATOR R-R TTL/CMOS 8MSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 比較器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:帶電壓基準 元件數:4 輸出類型:開路漏極 電壓 - 電源，單路/雙路(±):2.5 V ~ 11 V，±1.25 V ~ 5.5 V 電壓 - 輸入偏移（最小值）:10mV @ 5V 電流 - 輸入偏壓（最小值）:- 電流 - 輸出（標準）:0.015mA @ 5V 電流 - 靜態（最大值）:8.5µA CMRR, PSRR（標準）:80dB CMRR，80dB PSRR 傳輸延遲（最大）:- 磁滯:- 工作溫度:0°C ~ 70°C 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 安裝類型:表面貼裝 包裝:管件 產品目錄頁面:1386 (CN2011-ZH PDF) |
| AD8469WBRMZ_PROMO | 制造商:Analog Devices 功能描述:COMPARATOR TTL / CMOS SINGLE |
| AD8469WBRMZ-RL | 功能描述:IC COMPARATOR R-R TTL/CMOS 8MSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 比較器 系列:- 標準包裝:25 系列:- 類型:帶電壓基準 元件數:4 輸出類型:CMOS，開路漏極，TTL 電壓 - 電源，單路/雙路(±):2 V ~ 11 V，±1 V ~ 5.5 V 電壓 - 輸入偏移（最小值）:10mV @ 5V 電流 - 輸入偏壓（最小值）:- 電流 - 輸出（標準）:0.015mA @ 5V 電流 - 靜態（最大值）:8.5µA CMRR, PSRR（標準）:80dB CMRR，80dB PSRR 傳輸延遲（最大）:12µs 磁滯:50mV 工作溫度:0°C ~ 70°C 封裝/外殼:16-DIP（0.300"，7.62mm） 安裝類型:通孔 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。