- 您現在的位置：買賣IC網 > PDF目錄3513 > AD8290ACPZ-R7 (Analog Devices Inc)IC SENSOR AMP CMOS G-50 16-LFCSP PDF資料下載
參數資料
| 型號： | AD8290ACPZ-R7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/20頁 |
| 文件大小： | 0K |
| 描述： | IC SENSOR AMP CMOS G-50 16-LFCSP |
| 產品培訓模塊： | Current Sense Amplifiers |
| 標準包裝： | 1 |
| 放大器類型： | 電流檢測 |
| 電路數： | 1 |
| -3db帶寬： | 250kHz |
| 電流 - 輸入偏壓： | 100pA |
| 電流 - 電源： | 1.2mA |
| 電壓 - 電源，單路/雙路(±)： | 2.6 V ~ 5.5 V，±1.3 V ~ 2.75 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-UFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 16-LFCSP-UQ |
| 包裝： | 標準包裝 |
| 其它名稱： | AD8290ACPZ-R7DKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
AD8290
Rev. B | Page 17 of 20
MAXIMIZING PERFORMANCE THROUGH PROPER
LAYOUT
To achieve the maximum performance of the AD8290, care
should be taken in the circuit board layout. The PCB surface
must remain clean and free of moisture to avoid leakage currents
between adjacent traces. Surface coating of the circuit board
reduces surface moisture and provides a humidity barrier,
reducing parasitic resistance on the board.
RSET should be placed close to RSET (Pin 11) and GND (Pin 10).
The paddle on the bottom of the package should not be connected
to any potential and should be floating.
For high impedance sources, the PCB traces from the AD8290
inputs should be kept to a minimum to reduce input bias
current errors.
POWER SUPPLY BYPASSING
The AD8290 uses internally generated clock signals to perform
autocorrection. As a result, proper bypassing is necessary to
achieve optimum performance. Inadequate or improper bypassing
of the supply lines can lead to excessive noise and offset voltage.
A 0.1 μF surface-mount capacitor should be connected between
Pin 2 (VCC) and Pin 10 (GND) when operating with a single
supply and should be located as close as possible to those two pins.
DUAL-SUPPLY OPERATION
The AD8290 can be configured to operate in dual-supply mode.
An example of such a circuit is shown in Figure 46, where the
AD8290 is powered by ±1.8 V supplies. When operating with
dual supplies, pins that are normally referenced to ground in the
single-supply mode, now need to be referenced to the negative
supply. These pins include the following: Pin 1, Pin 7, Pin 8, Pin 9,
Pin 10, Pin 12, and Pin 16. External components, such as RSET, the
sensing bridge, and the antialiasing filter capacitor at the output,
should also be referenced to the negative supply. Additionally,
two bypass capacitors should be added beyond what is necessary
for single-supply operation: one between the negative supply
and ground, and the other between the positive and negative
supplies.
When operating in dual-supply mode, the specifications change
and become relative to the negative supply. The input voltage
range minimum shifts from 0.2 V to 0.2 V above the negative
supply (in this example: 1.6 V), the output voltage range shifts
from a minimum of 0.075 V to 0.075 V above the negative supply
(in this example: 1.725 V), and the excitation current pin
voltage minimum shifts from 0 V to 1.8 V in this example.
The maximum specifications of these three parameters are
For other specifications, both the minimum and maximum
specifications change. The output offset shifts from a minimum
of +865 mV and maximum of +935 mV to a minimum of
935 mV and a maximum of 865 mV in the example. In
addition, the logic levels for the ENBL operation should be
adjusted accordingly.
0
67
45-
0
29
CBRIDGE
NC = NO CONNECT
ENBL
VOUT
VOUT
VCC
VINP
VINN
IOUT
RSET
GND
AD8290
4
3
2
10
11
15
14
13
CFILTER
6.8nF
C1
0.1F
CF2
CF1
5
6
C2
68nF
RSET
692 TO 3k
1.8V
C3
0.1F
–1.8V
C5
0.1F
NC
16
1
12
9
7
8
–1.8V
NOTES
LAYOUT CONSIDERATIONS:
1. KEEP C1 CLOSE TO PIN 2 AND PIN 10.
2. KEEP C3 CLOSE TO PIN 2.
3. KEEP C5 CLOSE TO PIN 10.
4. KEEP RSET CLOSE TO PIN 11.
Figure 46. Typical Dual-Supply Connections
相關PDF資料 |
PDF描述 |
|---|---|
| AD8221ARZ-R7 | IC AMP INST PREC LN 18MA 8SOIC |
| MMS-129-02-L-DH | CONN RCPT 2MM 58POS DL HORZ SMD |
| TSW-137-23-S-S | CONN HEADER 37POS .100" SGL GOLD |
| TSW-147-14-T-D | CONN HEADER 94POS .100" DUAL TIN |
| MMS-102-02-L-DH | CONN RCPT 2MM 4POS DL HORZ SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8290ACPZ-RL | 功能描述:IC AMP CS CMOS LP 16LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| AD8293 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Noise, Low Gain Drift, G = 2000 Instrumentation Amplifier |
| AD8293G160 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost, Zero-Drift In-Amp with Filter and Fixed Gain |
| AD8293G160ARJZ-R2 | 功能描述:IC AMP INST R-R LDRIFT SOT23-8 RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:160 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:10 V/µs 增益帶寬積:9MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:250µV 電流 - 電源:730µA 電流 - 輸出 / 通道:28mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC N 包裝:管件 |
| AD8293G160ARJZ-R7 | 功能描述:IC AMP INST R-R LDRIFT SOT23-8 RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT |
發布緊急采購，3分鐘左右您將得到回復。