- 您現在的位置：買賣IC網 > PDF目錄373940 > AD818 (Analog Devices, Inc.) Low Cost, Low Power Video Op Amp(低成本,低功耗視頻運放) PDF資料下載
參數資料
| 型號： | AD818 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Low Cost, Low Power Video Op Amp(低成本,低功耗視頻運放) |
| 中文描述： | 低成本，低功耗視頻運算放大器（低成本，低功耗視頻運放） |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 535K |
| 代理商： | AD818 |
AD818
REV. A
–10–
–IN
+IN
NULL 1
NULL 8
OUTPUT
+V
S
–V
S
Figure 34. AD818 Simplified Schematic
T HE ORY OF OPE RAT ION
T he AD818 is a low cost, video operational amplifier designed
to excel in high performance, high output current video
applications.
T he AD818 (Figure 34) consists of a degenerated NPN differ-
ential pair driving matched PNPs in a folded-cascode gain stage.
T he output buffer stage employs emitter followers in a class AB
amplifier which delivers the necessary current to the load, while
maintaining low levels of distortion.
T he AD818 will drive terminated cables and capacitive loads of
10 pF or less. As the closed-loop gain is increased, the AD818
will drive heavier cap loads without oscillating.
INPUT CONSIDE RAT IONS
An input protection resistor (R
IN
in Figure 28) is required in
circuits where the input to the AD818 will be subjected to tran-
sient of continuous overload voltages exceeding the
±
6 V maxi-
mum differential limit. T his resistor provides protection for the
input transistors by limiting their maximum base current.
For high performance circuits, it is recommended that a “bal-
ancing” resistor be used to reduce the offset errors caused by
bias current flowing through the input and feedback resistors.
T he balancing resistor equals the parallel combination of R
IN
and R
F
and thus provides a matched impedance at each input
terminal. T he offset voltage error will then be reduced by more
than an order of magnitude.
GROUNDING AND BY PASSING
When designing high frequency circuits, some special precau-
tions are in order. Circuits must be built with short interconnect
leads. When wiring components, care should be taken to pro-
vide a low resistance, low inductance path to ground. Sockets
should be avoided, since their increased interlead capacitance
can degrade circuit bandwidth.
Feedback resistors should be of low enough value (
≤
1 k
) to
assure that the time constant formed with the inherent stray
capacitance at the amplifier’s summing junction will not limit
performance. T his parasitic capacitance, along with the parallel
resistance of R
F
/R
IN
, form a pole in the loop transmission which
may result in peaking. A small capacitance (1–5 pF) may be
used in parallel with the feedback resistor to neutralize this
effect.
Power supply leads should be bypassed to ground as close as
possible to the amplifier pins. Ceramic disc capacitors of
0.1
μ
F are recommended.
10k
1
7
6
8
4
3
2
–V
S
V
OS
ADJUST
+V
S
AD818
Figure 35. Offset Null Configuration
OFFSE T NULLING
T he input offset voltage of the AD818 is inherently very low.
However, if additional nulling is required, the circuit shown in
Figure 35 can be used. T he null range of the AD818 in this
configuration is
±
10 mV.
SINGLE SUPPLY OPE RAT ION
Another exciting feature of the AD818 is its ability to perform
well in a single supply configuration. T he AD818 is ideally
suited for applications that require low power dissipation and
high output current.
Referring to Figure 36, careful consideration should be given to
the proper selection of component values. T he choices for
this particular circuit are: R1 + R3
i
R2 combine with C1 to
form a low frequency corner of approximately 10 kHz. C4 was
inserted in series with R4 to maintain amplifier stability at high
frequency.
Combining R3 with C2 forms a low pass filter with a corner
frequency of approximately 500 Hz. T his is needed to maintain
amplifier PSRR, since the supply is connected to V
IN
through
the input divider. T he values for R2 and C2 were chosen to
demonstrate the AD818’s exceptional output drive capability. In
this configuration, the output is centered around 2.5 V. In order
to eliminate the static dc current associated with this level, C3
was inserted in series with R
L
.
R2
3.3k
R1
3.3k
R3
100
C2
3.3μF
V
IN
C1
0.01μF
C4
0.001μF
R4
1k
3
2
AD818
V
OUT
+V
S
7
3.3μF
0.01μF
4
SELECT C1, R1, R2
FOR DESIRED LOW
FREQUENCY CORNER.
6
C3
0.1μF
R
L
150
1k
Figure 36. Single Supply Amplifier Configuration
相關PDF資料 |
PDF描述 |
|---|---|
| AD8190 | 2:1 HDMI/DVI Switch with Equalization |
| AD8190ACPZ | 2:1 HDMI/DVI Switch with Equalization |
| AD8190ACPZ-R7 | 2:1 HDMI/DVI Switch with Equalization |
| AD8190-EVAL | 2:1 HDMI/DVI Switch with Equalization |
| AD8200 | High Common-Mode Voltage, Single Supply Difference Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD818_03 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost, Low Power Video Op Amp |
| AD818_10 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost, Low Power Video Op Amp |
| AD8180 | 制造商:AD 制造商全稱:Analog Devices 功能描述:750 MHz, 3.8 mA 10 ns Switching Multiplexers |
| AD8180AN | 制造商:Analog Devices 功能描述:Analog Multiplexer Single 2:1 8-Pin PDIP 制造商:Rochester Electronics LLC 功能描述:PDIP 2:1 WIDEBAND MULTIPLEXER - Bulk |
| AD8180ANZ | 功能描述:IC MULTIPLEXER 2X1 8DIP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 其它有關文件:STG4159 View All Specifications 標準包裝:5,000 系列:- 功能:開關 電路:1 x SPDT 導通狀態電阻:300 毫歐 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±1.65 V ~ 4.8 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:7-WFBGA，F(xiàn)CBGA 供應商設備封裝:7-覆晶 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。