參數資料
型號： AD8129-EVAL
廠商： Analog Devices, Inc.
英文描述： Low-Cost 270 MHz Differential Receiver Amplifiers
中文描述： 低成本270 MHz的差分接收器放大器
文件頁數： 21/28頁
文件大?。?/td> 510K
代理商： AD8129-EVAL
REV. 0
AD8129/AD8130
–21–
APPLICATIONS
Basic Gain Circuits
The gain of the AD8129/AD8130 can be set with a pair of feed-
back resistors. The basic configuration is shown in Figure 5.
The gain equation is the same as that of a conventional op amp:
G = 1 + R
F
/R
G
. For unity gain applications using the AD8130,
R
F
can be set to zero (short circuit), and R
G
can be removed.
(See Figure 6.) The AD8129 is compensated to operate at gains
of 10 and higher, so shorting the feedback path to obtain unity
gain will cause oscillation.
R
F
R
G
0.1 F
10 F
–
V
V
OUT
+V
0.1 F
10 F
V
IN
–
V
S
PD
+V
S
+
+
AD8129/
AD8130
Figure 5. Basic Gain Circuit: V
OUT
= V
IN
(1 + R
F
/R
G
)
0.1 F 10 F
–
V
V
OUT
+V
0.1 F
10 F
V
IN
AD8130
–
V
S
PD
+V
S
+
+
Figure 6. An AD8130 with Unity Gain
The input signal can be applied either differentially or single-
endedly—all that matters is the magnitude of the differential
signal between the two inputs. For single-ended input applica-
tions, applying the signal to the +IN with –IN grounded will
create a noninverting gain, while reversing these connections
will create an inverting gain. Since the two inputs are high-
impedance and matched, both of these conditions will provide
the same high input impedance. Thus, an advantage of the
active feedback architecture is the ability to make a high-input-
impedance, inverting op amp. If conventional op amps are used,
a high impedance buffer followed by an inverting stage is needed.
This requires two op amps.
Twisted-Pair Cable, Composite Video Receiver with Equal-
ization Using an AD8130
The AD8130 has excellent common-mode rejection at its inputs.
This makes it an ideal candidate for a receiver for signals that
are transmitted over long distances on twisted-pair cables. Cat-
egory 5 type cables are now very common in office settings and
are extensively used for data transmission. These same cables
can also be used for the analog transmission of signals like video.
These long cables will pick up noise from the environment they
pass through. This noise will not favor one conductor over an-
other, and will therefore be a common-mode signal. A receiver
that rejects the common-mode signal on the cable can greatly
enhance the signal-to-noise ratio performance of the link.
The AD8130 is also very easy to use as a differential receiver,
because the differential inputs and the feedback inputs are
entirely separate. This means that there is no interaction of the
feedback network and the termination network as there would
be in conventional op amp-type receivers.
Another issue to be dealt with on long cables is the attenuation
of the signal at longer distances. This attenuation is a function of
frequency and increases as roughly as the square root of frequency.
For good fidelity of video circuits, the overall frequency response
of the transmission channel should be flat versus frequency. Since
the cable attenuates the high frequencies, a frequency-selective
boost circuit can be used to undo this effect. These circuits
are called equalizers.
An equalizer uses frequency-dependent elements (Ls and Cs) in
order to create a frequency response that is the opposite of the
rest of the channel’s response in order to create an overall flat
response. There are many ways to create such circuits, but a
common technique is to put the frequency-selective elements in
the feedback path of an op amp circuit. The AD8130 in particu-
lar makes this easier than other circuits, because, once again, the
feedback path is totally independent of the input path and there
is no interaction.
The circuit in Figure 7 was developed as a receiver/equalizer for
transmitting composite video over 300 m of Category 5 cable. This
cable has an attenuation of approximately 20 dB at 10 MHz
for 300 m. At 100 MHz, the attenuation is approximately
60 dB. (See Figure 8.)
R
F
1k
0.1 F
10 F
–
V
V
OUT
+V
0.1 F
10 F
V
IN
R1
100
R
G
499
–
V
S
PD
+V
S
+
+
C1
200pF
AD8130
100
Figure 7. An Equalizer Circuit for Composite Video
Transmission over 300 m of Category 5 Cable
相關PDF資料
PDF描述
AD8129AR-REEL1 Low-Cost 270 MHz Differential Receiver Amplifiers
AD8129AR-REEL72 Low-Cost 270 MHz Differential Receiver Amplifiers
AD8130ARZ-REEL Low Cost 270 MHz Differential Receiver Amplifiers
AD8130ARZ-REEL7 Low Cost 270 MHz Differential Receiver Amplifiers
AD8129ARM-REEL Low Cost 270 MHz Differential Receiver Amplifiers
相關代理商/技術參數
參數描述
AD812AN 制造商:Analog Devices 功能描述:OP Amp Dual Current Fdbk 制造商:Rochester Electronics LLC 功能描述:DUAL LO PWR I-FDBK OP AMP - Bulk 制造商:Analog Devices 功能描述:IC OP-AMP LOW POWER
AD812ANZ 功能描述:IC OPAMP DUAL CURR-FDBK 8-DIP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件
AD812AR 功能描述:IC OPAMP DUAL CURR-FDBK 8-SOIC RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR)
AD812AR-8 制造商:Analog Devices 功能描述:
AD812AR-EBZ 功能描述:BOARD EVAL FOR AD812AR RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*