參數資料
型號： AD8129-EVAL
廠商： Analog Devices, Inc.
英文描述： Low-Cost 270 MHz Differential Receiver Amplifiers
中文描述： 低成本270 MHz的差分接收器放大器
文件頁數： 20/28頁
文件大?。?/td> 510K
代理商： AD8129-EVAL
REV. 0
AD8129/AD8130
–20–
THEORY OF OPERATION
The AD8129/AD8130 use an architecture called active feed-
back which differs from that of conventional op amps. The
most obvious differentiating feature is the presence of two sepa-
rate pairs of differential inputs compared to a conventional op
amp’s single pair. Typically for the active-feedback architecture,
one of these input pairs is driven by a differential input signal,
while the other is used for the feedback. This active stage in the
feedback path is where the term “active feedback” is derived.
The active feedback architecture offers several advantages over a
conventional op amp in several types of applications. Among
these are excellent common-mode rejection, wide input common-
mode range and a pair of inputs that are high-impedance and
totally balanced in a typical application. In addition, while an
external feedback network establishes the gain response as
in a conventional op amp, its separate path makes it totally
independent of the signal input. This eliminates any interaction
between the feedback and input circuits, which traditionally
causes problems with CMRR in conventional differential-input
op amp circuits.
Another advantage is the ability to change the polarity of the
gain merely by switching the differential inputs. A high input-
impedance inverting amplifier can be made. Besides a high
input impedance, a unity-gain inverter with the AD8130 will
have a noise gain of unity. This will produce lower output noise
and higher bandwidth than op amps that have noise gain equal
to 2 for a unity gain inverter.
The two differential input stages of the AD8129/AD8130 are each
transconductance stages that are well matched. These stages
convert the respective differential input voltages to internal
currents. The currents are then summed and converted to a
voltage, which is buffered to drive the output. The compensa-
tion capacitor is in the summing circuit.
When the feedback path is closed around the part, the output
will drive the feedback input to that voltage which causes the
internal currents to sum to zero. This occurs when the two
differential inputs are equal and opposite; that is, their algebraic
sum is zero.
In a closed-loop application, a conventional op amp will have its
differential input voltage driven to near zero under nontransient
conditions. The AD8129/AD8130 generally will have differential
input voltages at each of its input pairs, even under equilibrium
conditions. As a practical consideration, it is necessary to inter-
nally limit the differential input voltage with a clamp circuit.
Thus, the input dynamic ranges are limited to about 2.5 V for
the AD8130 and 0.5 V for the AD8129 (see Specification
section for more detail). For this and other reasons, it is not
recommended to reverse the input and feedback stages of the
AD8129/AD8130, even though some apparently normal func-
tionality might be observed under some conditions.
A few simple circuits can illustrate how the active feedback
architecture of the AD8129/AD8130 operates.
Op Amp Configuration
If only one of the input stages of the AD8129/AD8130 is used,
it will function very much like a conventional op amp. (See
Figure 4.) Classical inverting and noninverting op amps circuits
can be created, and the basic governing equations will be the
same as for a conventional op amp. The unused input pins form
the second input and should be shorted together and tied to
ground or some midsupply voltage when they are not used.
–
V
S
PD
+
V
S
+
+
R
F
R
G
0.1 F
10 F
–
V
V
OUT
V
IN
+V
0.1 F
10 F
Figure 4. With both inputs grounded, the feedback stage
functions like an op amp: V
OUT
= V
IN
(1 + R
F
/R
G
). NOTE: This
circuit is provided to demonstrate device operation. It is
not suggested to use this circuit in place of an op amp.
With the unused pair of inputs shorted, there is no differential
voltage between them. This dictates that the differential input
voltage of the used inputs will also be zero for closed-loop
applications. Since this is the governing principle of conven-
tional op amp circuits, an active feedback amplifier can function
as a conventional op amp under these conditions.
Note that this circuit is presented only for illustration purposes,
to show the similarities of the active feedback architecture func-
tionality to conventional op amp functionality. If it is desired to
design a circuit that can be created from a conventional op amp,
it is recommended to choose a conventional op amp whose
specifications are better suited to that application. These op amp
principles are the basis for offsetting the output as described in
the Output Offset/Level Translator section.
相關PDF資料
PDF描述
AD8129AR-REEL1 Low-Cost 270 MHz Differential Receiver Amplifiers
AD8129AR-REEL72 Low-Cost 270 MHz Differential Receiver Amplifiers
AD8130ARZ-REEL Low Cost 270 MHz Differential Receiver Amplifiers
AD8130ARZ-REEL7 Low Cost 270 MHz Differential Receiver Amplifiers
AD8129ARM-REEL Low Cost 270 MHz Differential Receiver Amplifiers
相關代理商/技術參數
參數描述
AD812AN 制造商:Analog Devices 功能描述:OP Amp Dual Current Fdbk 制造商:Rochester Electronics LLC 功能描述:DUAL LO PWR I-FDBK OP AMP - Bulk 制造商:Analog Devices 功能描述:IC OP-AMP LOW POWER
AD812ANZ 功能描述:IC OPAMP DUAL CURR-FDBK 8-DIP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件
AD812AR 功能描述:IC OPAMP DUAL CURR-FDBK 8-SOIC RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR)
AD812AR-8 制造商:Analog Devices 功能描述:
AD812AR-EBZ 功能描述:BOARD EVAL FOR AD812AR RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*