參數資料
型號: AD7934BRUZ-REEL7
廠商: Analog Devices Inc
文件頁數: 18/32頁
文件大?。?/td> 0K
描述: IC ADC 12BIT 4CH 1.5MSPS 28TSSOP
標準包裝: 1,000
位數: 12
采樣率(每秒): 1.5M
數據接口: 并聯
轉換器數目: 1
功率耗散(最大): 13.5mW
電壓電源: 單電源
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 28-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 28-TSSOP
包裝: 帶卷 (TR)
輸入數目和類型: 4 個單端,單極;2 個差分,單極;2 個偽差分,單極
AD7933/AD7934
Rev. B | Page 25 of 32
Writing Data to the AD7933/AD7934
With W/B tied logic high, a single write operation transfers the
full data-word on DB0 to DB11 to the control register on the
AD7933/AD7934. The DB8/HBEN pin assumes its DB8
function. Data written to the AD7933/AD7934 should be
provided on the DB0 to DB11 inputs, with DB0 being the LSB
of the data-word. With W/B tied logic low, the AD7933/AD7934
requires two write operations to transfer a full 12-bit word.
DB8/HBEN assumes its HBEN function. Data written to the
AD7933/AD7934 should be provided on the DB0 to DB7
inputs. HBEN determines whether the byte written is high byte
or low byte data. The low byte of the data-word has DB0 being
the LSB of the full data-word. For the high byte write, HBEN
should be high and the data on the DB0 input should be Data
Bit 8 of the 12-bit word.
Figure 36 shows the write cycle timing diagram of the
AD7933/AD7934 in word mode. When operating in word
mode, the HBEN input does not exist and only one write
operation is required to write the word of data to the device.
Provide data on DB0 to DB11. When operating in byte mode,
the two write cycles shown in Figure 37 are required to write the
full data-word to the AD7933/AD7934. In Figure 37, the first
write transfers the lower eight bits of the data-word from DB0
to DB7, and the second write transfers the upper four bits of the
data-word.
When writing to the AD7933/AD7934, the top four bits in the
high byte must be 0s.
The data is latched into the device on the rising edge of WR.
The data needs to be set up a time, t7, before the WR rising
edge and held for a time, t8, after the WR rising edge. The CS
and WR signals are gated internally. CS and WR can be tied
together as the timing specifications for t4 and t5 are 0 ns
minimum (assuming CS and RD have not already been tied
together).
t8
t5
t7
t6
t4
DATA
DB0 TO DB11
WR
CS
037
13-
00
2
Figure 36. AD7933/AD7934 Parallel Interface—Write Cycle Timing for Word Mode Operation (W/B = 1)
t5
t4
t7
t18
t19
t8
t6
t17
LOW BYTE
HIGH BYTE
DB0 TO DB7
HBEN/DB8
WR
CS
0
371
3-
003
Figure 37. AD7933/AD7934 Parallel Interface—Write Cycle Timing for Byte Mode Operation (W/B = 0)
相關PDF資料
PDF描述
MS3106F22-23S CONN PLUG 8POS STRAIGHT W/SCKT
MS27467T11F99S CONN PLUG 7POS STRAIGHT W/SCKT
SI8244CB-C-IS1 IC AUDIO DRIVER PWM 16-SOIC
MS27467E9B44S CONN PLUG 4POS STRAIGHT W/SCKT
SI8244BB-C-IS1 IC AUDIO DRIVER PWM 16-SOIC
相關代理商/技術參數
參數描述
AD7937 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS 8+4 Loading Dual 12-Bit DAC
AD7937AR 功能描述:IC DAC 12BIT DUAL 8+4 24-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散(最大):- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率(每秒):*
AD7937AR-REEL 功能描述:IC DAC 12BIT DUAL 8+4 24-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散(最大):- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率(每秒):*
AD7937AR-REEL7 制造商:Analog Devices 功能描述:DAC 2CH R-2R 12-BIT 24SOIC W - Tape and Reel
AD7937BR 功能描述:IC DAC 12BIT DUAL 8+4 24-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散(最大):- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率(每秒):*