參數資料
型號: AD7934BRUZ-REEL7
廠商: Analog Devices Inc
文件頁數: 16/32頁
文件大?。?/td> 0K
描述: IC ADC 12BIT 4CH 1.5MSPS 28TSSOP
標準包裝: 1,000
位數: 12
采樣率(每秒): 1.5M
數據接口: 并聯
轉換器數目: 1
功率耗散(最大): 13.5mW
電壓電源: 單電源
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 28-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 28-TSSOP
包裝: 帶卷 (TR)
輸入數目和類型: 4 個單端,單極;2 個差分,單極;2 個偽差分,單極
AD7933/AD7934
Rev. B | Page 23 of 32
PARALLEL INTERFACE
The AD7933/AD7934 have a flexible, high speed, parallel
interface. This interface is 10 bits (AD7933) or 12 bits (AD7934)
wide and is capable of operating in either word (W/B tied high)
or byte (W/B tied low) mode. The CONVST signal is used to
initiate conversions and, when operating in autoshutdown or
autostandby mode, it is used to initiate power-up.
A falling edge on the CONVST signal is used to initiate
conversions, and it also puts the ADC track-and-hold into
track. Once the CONVST signal goes low, the BUSY signal goes
high for the duration of the conversion. In between conversions,
CONVST must be brought high for a minimum time of t1. This
must happen after the 14th falling edge of CLKIN; otherwise, the
conversion is aborted and the track-and-hold goes back into track.
At the end of the conversion, BUSY goes low and can be used to
activate an interrupt service routine. The CS and RD lines are
then activated in parallel to read the 10 bits or 12 bits of
conversion data. When power supplies are first applied to the
device, a rising edge on CONVST is necessary to put the track-
and-hold into track. The acquisition time of 125 ns minimum
must be allowed before CONVST is brought low to initiate a
conversion. The ADC then goes into hold on the falling edge of
CONVST and back into track on the 13th rising edge of CLKIN
after this (see Figure 34). When operating the device in
autoshutdown or autostandby mode, where the ADC powers
down at the end of each conversion, a rising edge on the
CONVST signal is used to power up the device.
t2
t3
t20
t14
t11
t9
t13
t12
t10
tCONVERT
tACQUISITION
tQUIET
t1
12
3
4
5
12
13
14
B
A
DATA
OLD DATA
DB0 TO DB11
RD
CS
INTERNAL
TRACK/HOLD
BUSY
CLKIN
CONVST
THREE-STATE
WITH CS AND RD TIED LOW
03
713
-00
4
Figure 34. AD7933/AD7934 Parallel Interface—Conversion and Read Cycle Timing in Word Mode (W/B = 1)
相關PDF資料
PDF描述
MS3106F22-23S CONN PLUG 8POS STRAIGHT W/SCKT
MS27467T11F99S CONN PLUG 7POS STRAIGHT W/SCKT
SI8244CB-C-IS1 IC AUDIO DRIVER PWM 16-SOIC
MS27467E9B44S CONN PLUG 4POS STRAIGHT W/SCKT
SI8244BB-C-IS1 IC AUDIO DRIVER PWM 16-SOIC
相關代理商/技術參數
參數描述
AD7937 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS 8+4 Loading Dual 12-Bit DAC
AD7937AR 功能描述:IC DAC 12BIT DUAL 8+4 24-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散(最大):- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率(每秒):*
AD7937AR-REEL 功能描述:IC DAC 12BIT DUAL 8+4 24-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散(最大):- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率(每秒):*
AD7937AR-REEL7 制造商:Analog Devices 功能描述:DAC 2CH R-2R 12-BIT 24SOIC W - Tape and Reel
AD7937BR 功能描述:IC DAC 12BIT DUAL 8+4 24-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散(最大):- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率(每秒):*