參數資料
型號： AD7877ACPZ-500RL7
廠商： Analog Devices Inc
文件頁數： 7/45頁
文件大小： 0K
描述： IC ADC 12BIT TOUCHSCREEN 32LFCSP
標準包裝： 1
類型： 電阻
觸摸面板接口： 4 線
輸入數/鍵： 1 TSC
分辨率（位）： 12 b
評估套件： 可供
數據接口： 串行，SPI?
數據速率/采樣率 (SPS，BPS)： 125k
電壓基準： 外部，內部
電源電壓： 2.7 V ~ 5.25 V
電流 - 電源： 1µA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 32-VFQFN 裸露焊盤，CSP
供應商設備封裝： 32-LFCSP-VQ
包裝： 標準包裝
其它名稱： AD7877ACPZ-500RL7DKR
AD7877
Data Sheet
Rev. D | Page 14 of 44
CIRCUIT INFORMATION
The AD7877 is a complete, 12-bit data acquisition system for
digitizing positional inputs from a touch screen in PDAs and
other devices. In addition, it can monitor two battery voltages,
ambient temperature, and three auxiliary analog voltages, with
high and low limit comparisons on three of the inputs, and has
up to four general-purpose logic I/O pins.
The core of the AD7877 is a high speed, low power, 12-bit
analog-to-digital converter (ADC) with input multiplexer,
on-chip track-and-hold, and on-chip clock. The results of
conversions are stored in 11 results registers, and the results
from one auxiliary input and two battery inputs can be com-
pared with high and low limits stored in limit registers to generate
an out-of-limit ALERT. The AD7877 also contains low resistance
analog switches to switch the X and Y excitation voltages to the
touch screen, a STOPACQ pin to control the ADC acquisition
period, 2.5 V reference, on-chip temperature sensor, and 8-bit
DAC to control LCD contrast. The high speed SPI serial bus
provides control of, and communication with, the device.
Operating from a single supply from 2.2 V to 5 V, the AD7877
offers throughput rates of up to 125 kHz. The device is available
in a 5 mm × 5 mm, 32-lead, lead frame chip scale package
(LFCSP), and in a 2.5 mm × 2.8 mm, wafer level chip scale
package (WLCSP), with a 5 × 5 ball grid array.
The data acquisition system of the AD7877 has a number of
advanced features:
Input channel sequenced automatically or selected by
the host.
STOPACQ feature to reduce noise from LCD.
Averaging of from 1 to 16 conversions for noise reduction.
Programmable acquisition time.
Power management.
Programmable ADC power-up delay before first
conversion.
Choice of internal or external reference.
Conversion at preprogrammed intervals.
TOUCH SCREEN PRINCIPLES
A 4-wire touch screen consists of two flexible, transparent,
resistive-coated layers that are normally separated by a small air
gap. The X layer has conductive electrodes running down the
left and right edges, allowing the application of an excitation
voltage across the X layer from left to right.
03796-005
X+
X–
Y–
Y+
CONDUCTIVE ELECTRODE
ON BOTTOM SIDE
PLASTIC FILM WITH
TRANSPARENT, RESISTIVE
COATING ON BOTTOM SIDE
PLASTIC FILM WITH
TRANSPARENT, RESISTIVE
COATING ON TOP SIDE
LCD SCREEN
CONDUCTIVE ELECTRODE
ON TOP SIDE
Figure 27. Basic Construction of a Touch Screen
The Y layer has conductive electrodes running along the top
and bottom edges, allowing the application of an excitation
voltage down the Y layer from top to bottom.
Provided that the layers are of uniform resistivity, the voltage at
any point between the two electrodes is proportional to the
horizontal position for the X layer and the vertical position for
the Y layer.
When the screen is touched, the two layers make contact. If
only the X layer is excited, the voltage at the point of contact,
and therefore the horizontal position, can be sensed at one of
the Y layer electrodes. Similarly, if only the Y layer is excited,
the voltage, and therefore the vertical position, can be sensed at
one of the X layer electrodes. By switching alternately between
X and Y excitation and measuring the voltages, the X and
Y coordinates of the contact point can be found.
In addition to measuring the X and Y coordinates, it is also
possible to estimate the touch pressure by measuring the
contact resistance between the X and Y layers. The AD7877 is
designed to facilitate this measurement.
Figure 28 shows an equivalent circuit of the analog input
structure of the AD7877, showing the touch screen switches,
the main analog multiplexer, the ADC with analog and
differential reference inputs, and the dual 3-to-1 multiplexer
that selects the reference source for the ADC.
相關PDF資料
PDF描述
D38999/20WJ29PD CONN RCPT 29POS WALL MNT W/PINS
D38999/20FJ29PB CONN RCPT 29POS WALL MNT W/PINS
D38999/20WJ29PB CONN RCPT 29POS WALL MNT W/PINS
SY100EL12ZI IC DRIVER LOW IMPEDANCE 8-SOIC
AD7873ACPZ IC ADC 12BIT TOUCHSCREEN 16LFCSP
相關代理商/技術參數
參數描述
AD7877ACPZ-REEL 功能描述:IC ADC 12BIT TOUCHSCREEN 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
AD7877ACPZ-REEL7 功能描述:IC ADC 12BIT TOUCHSCREEN 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
AD7877WACPZ-REEL7 功能描述:IC CTRLR TOUCH SCREEN 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
AD7878 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Complete 12-Bit 100 kHz Sampling ADC with DSP Interface
AD7878AQ 制造商:Rochester Electronics LLC 功能描述:COMPLETE 12 BIT ADC IC - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*