- 您現在的位置：買賣IC網 > PDF目錄10084 > AD7703CR-REEL (Analog Devices Inc)IC ADC 20BIT LC2MOS MONO 20-SOIC PDF資料下載
參數資料
| 型號： | AD7703CR-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 12/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 20BIT LC2MOS MONO 20-SOIC |
| 標準包裝： | 1,000 |
| 位數： | 20 |
| 采樣率（每秒）： | 4k |
| 數據接口： | 串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 37mW |
| 電壓電源： | 模擬和數字，雙 ± |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 20-SOIC W |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個單端，單極；1 個單端，雙極 |
REV. E
AD7703
–5–
DATA
VALID
t
15
HI-Z
SDATA
CS
Figure 5b. SEC Mode Data Hold Time
HI-Z
DB19
DB18
DB1
DB0
HI-Z
SCLK
SDATA
CLKIN
CS
HI-Z
t
7
t
8
t
5
t
9
t
4
t
8
HI-Z
Figure 6. SSC Mode Timing Diagram
DEFINITION OF TERMS
Linearity Error
This is the maximum deviation of any code from a straight line
passing through the endpoints of the transfer function. The
endpoints of the transfer function are zero-scale (not to be
confused with bipolar zero), a point 0.5 LSB below the first code
transition (000 . . . 000 to 000 . . . 001) and full-scale, a point
1.5 LSB above the last code transition (111 . . . 110 to 111 . . .
111). The error is expressed as a percentage of full scale.
Differential Linearity Error
This is the difference between any code’s actual width and the
ideal (1 LSB) width. Differential linearity error is expressed in
LSB. A differential linearity specification of
± 1 LSB or less
guarantees monotonicity.
Positive Full-Scale Error
Positive full-scale error is the deviation of the last code transition
(111 . . . 110 to 111 . . . 111) from the ideal (VREF
±3/2 LSB).
It applies to both positive and negative analog input ranges and
is expressed in microvolts.
Unipolar Offset Error
Unipolar offset error is the deviation of the first code transition
from the ideal (AGND + 0.5 LSB) when operating in the
Unipolar mode.
Bipolar Zero Error
This is the deviation of the midscale transition (0111 . . . 111 to
1000 . . . 000) from the ideal (AGND – 0.5 LSB) when operating
in the Bipolar mode. It is expressed in microvolts.
Bipolar Negative Full-Scale Error
This is the deviation of the first code transition from the ideal
(–VREF + 0.5 LSB) when operating in the Bipolar mode.
Positive Full-Scale Overrange
Positive full-scale overrange is the amount of overhead available
to handle input voltages greater than +VREF (for example, noise
peaks or excess voltages due to system gain errors in system
calibration routines) without introducing errors due to overloading
the analog modulator or overflowing the digital filter.
Negative Full-Scale Overrange
This is the amount of overhead available to handle voltages below
–VREF without overloading the analog modulator or overflowing
the digital filter. Note that the analog input will accept negative
voltage peaks even in the Unipolar mode.
Offset Calibration Range
In the system calibration modes (SC2 low), the AD7703 calibrates
its offset with respect to the AIN pin. The offset calibration range
specification defines the range of voltages, expressed as a
percentage of VREF, that the AD7703 can accept and still accurately
calibrate offset.
Full-Scale Calibration Range
This is the range of voltages that the AD7703 can accept in the
system calibration mode and still correctly calibrate full scale.
Input Span
In system calibration schemes, two voltages applied in sequence
to the AD7703’s analog input define the analog input range. The
input span specification defines the minimum and maximum
input voltages from zero to full scale that the AD7703 can accept
and still accurately calibrate gain. The input span is expressed
as a percentage of VREF.
DATA
VALID
t
10
HI-Z
SDATA
CS
Figure 4. SSC Mode Data Hold Time
HI-Z
DB18
DB1
DB0
HI-Z
SDATA
DRDY
CS
t
12
t
11
t
13
t
14
SCLK
t
16
DB19
Figure 5a. SEC Mode Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| IDT72221L15PF | IC FIFO SYNC 1KX9 15NS 32QFP |
| MS27466T23F55PB | CONN RCPT 55POS WALL MT W/PINS |
| VE-2NF-MX-F4 | CONVERTER MOD DC/DC 72V 75W |
| VI-B32-IV-F2 | CONVERTER MOD DC/DC 15V 150W |
| VI-23L-IW-F4 | CONVERTER MOD DC/DC 28V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7703CRZ | 功能描述:IC ADC 20BIT LC2MOS MONO 20SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7703SQ | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS 20-Bit A/D Converter |
| AD7705 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V/5 V, 1 mW 2-/3-Channel 16-Bit, Sigma-Delta ADCs |
| AD7705_06 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V/5 V, 1 mW, 2-/3-Channel, 16-Bit, Sigma-Delta ADCs |
| AD7705BN | 功能描述:IC ADC 16BIT 2CH 16-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。