- 您現在的位置：買賣IC網 > PDF目錄1982 > AD7689BCPZRL7 (Analog Devices Inc)IC ADC 16BIT 250KSPS 8CH 20LFCSP PDF資料下載
參數資料
| 型號： | AD7689BCPZRL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 21/32頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 250KSPS 8CH 20LFCSP |
| 產品培訓模塊： | Power Line Monitoring Motor Control |
| 產品變化通告： | Startup Circuitry Design Improvement Change 15/April/2009 |
| 標準包裝： | 1 |
| 系列： | PulSAR® |
| 位數： | 16 |
| 采樣率（每秒）： | 250k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 21mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 20-LFCSP-VQ |
| 包裝： | 標準包裝 |
| 輸入數目和類型： | 8 個單端，單極；4 個差分，雙極；4 個偽差分，雙極 |
| 其它名稱： | AD7689BCPZRL7DKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7682/AD7689
Data Sheet
Rev. D | Page 28 of 32
CHANNEL SEQUENCER
scanning channels in a repeated fashion. Channels are scanned
as singles or pairs, with or without the temperature sensor, after
the last channel is sequenced.
The sequencer starts with IN0 and finishes with IN[7:0] set in
CFG[9:7]. For paired channels, the channels are paired depend-
ing on the last channel set in CFG[9:7]. Note that in sequencer
mode, the channels are always paired with the positive input on
the even channels (IN0, IN2, IN4, IN6), and with the negative
input on the odd channels (IN1, IN3, IN5, IN7). For example,
setting CFG[9:7] = 110 or 111 scans all pairs with the positive
inputs dedicated to IN0, IN2, IN4, and IN6.
CFG[2:1] are used to enable the sequencer. After the CFG
register is updated, DIN must be held low while reading data
out for Bit 13, or the CFG register begins updating again.
Note that while operating in a sequence, some bits of the CFG
register can be changed. However, if changing CFG[11] (paired
or single channel) or CFG[9:7] (last channel in sequence), the
sequence reinitializes and converts IN0 (or IN0/IN1 pairs) after
the CFG register is updated.
Figure 39 details the timing for all three modes without a busy
indicator. Refer to the Read/Write Spanning Conversion
Without a Busy Indicator section and the Read/Write Spanning
Conversion Without a Busy Indicator section for more details.
The sequencer can also be used with the busy indicator and
details for these timings can be found in the General Timing
with a Busy Indicator section and the Read/Write Spanning
Conversion with a Busy Indicator section.
For sequencer operation, the CFG register should be set during
the (n 1) phase after power-up. On phase (n), the sequencer
setting takes place and acquires IN0. The first valid conversion
result is available at phase (n + 1). After the last channel set in
CFG[9:7] is converted, the internal temperature sensor data is
output (if enabled), followed by acquisition of IN0.
Examples
With all channels configured for unipolar mode to GND,
including the internal temperature sensor, the sequence scans in
the following order:
IN0, IN1, IN2, IN3, IN4, IN5, IN6, IN7, TEMP, IN0, IN1, IN2, …
For paired channels with the internal temperature sensor
enabled, the sequencer scans in the following order:
IN0, IN2, IN4, IN6, TEMP, IN0, …
Note that IN1, IN3, IN5, and IN7 are referenced to a GND
ACQUISITION
(n – 1) UNDEFINED
ACQUISITION
(n), IN0
ACQUISITION
(n + 1), IN1
ACQUISITION
(n + 2), IN2
PHASE
POWER
UP
EOC
SOC
EOC
CONVERSION
(n – 1) UNDEFINED
CONVERSION
(n), IN0
CONVERSION
(n + 1), IN1
CONVERSION
(n – 2) UNDEFINED
07
35
3-
0
4
6
tCONV
tCYC
tDATA
CNV
DIN
SDO
XXX
MSB
XXX
MSB
XXX
NOTES
1. CNV MUST BE HIGH PRIOR TO THE END OF CONVERSION (EOC) TO AVOID THE BUSY INDICATOR.
2. A TOTAL OF 16 SCK FALLING EDGES ARE REQUIRED TO RETURN SDO TO HIGH-Z. IF CFG READBACK IS ENABLED,
A TOTAL OF 30 SCK FALLING EDGES IS REQUIRED TO RETURN SDO TO HIGH-Z.
DATA IN0
DATA (n – 1)
XXX
DATA (n – 1)
XXX
DATA (n – 1)
XXX
DATA (n – 1)
XXX
DATA (n – 2)
XXX
DATA (n – 2)
XXX
DATA (n – 2)
XXX
DATA (n – 2)
XXX
DATA (n – 3)
XXX
MSB
IN0
MSB
IN1
DIN
SDO
DATA IN1
DATA IN0
DATA IN1
DIN
CFG (n)
SDO
SCK
1
NOTE 1
16
NOTE 2
2
1
SCK
116
16
nn
n
n + 1
n
1
SCK
1
116
16
1
CFG (n)
RDC
RAC
RSC
CFG (n)
Figure 39. General Channel Sequencer Timing Without a Busy Indicator
相關PDF資料 |
PDF描述 |
|---|---|
| AD7690BCPZRL | IC ADC 18BIT 400KSPS 10-LFCSP |
| AD7691BCPZRL7 | IC ADC 18BIT SAR 250KSPS 10LFCSP |
| AD7693BRMZRL7 | IC ADC 16BIT 500KSPS 10-MSOP |
| AD7694ARMZ | IC ADC 16BIT SAR 250KSPS 8MSOP |
| AD7699BCPZRL7 | IC ADC 8CH 16BIT 500KSPS 20LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD768ACHIPS | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 30 MSPS D/A Converter |
| AD768AF/QMLR | 制造商:Analog Devices 功能描述: |
| AD768AR | 功能描述:IC DAC 16BIT 30MSPS 28-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
發布緊急采購，3分鐘左右您將得到回復。