參數資料
型號： AD7685CRMZRL7
廠商： Analog Devices Inc
文件頁數： 28/28頁
文件大?。?/td> 0K
描述： IC ADC 16BIT PSEUDO-DIFF 10MSOP
產品培訓模塊： Power Line Monitoring
Motor Control
設計資源： Parametric Measurement Unit and Supporting Components for PAD Appls Using AD5522 and AD7685 (CN0104)
Integrated Device Power Supply for PAD with Output Voltage Range 0 V to 25 V (CN0130)
標準包裝： 1,000
系列： PulSAR®
位數： 16
采樣率（每秒）： 250k
數據接口： DSP，MICROWIRE?，QSPI?，串行，SPI?
轉換器數目： 1
功率耗散（最大）： 15mW
電壓電源： 模擬和數字
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 10-TFSOP，10-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 10-MSOP
包裝： 帶卷 (TR)
輸入數目和類型： 1 個偽差分，單極
配用： EVAL-AD7685CBZ-ND - BOARD EVAL FOR AD7685
AD7685
Rev. C | Page 9 of 28
TERMINOLOGY
Integral Nonlinearity Error (INL)
INL refers to the deviation of each individual code from a line
drawn from negative full scale through positive full scale. The
point used as negative full scale occurs LSB before the first
code transition. Positive full scale is defined as a level 1 LSB
beyond the last code transition. The deviation is measured from
the middle of each code to the true straight line (see Figure 26).
Differential Nonlinearity Error (DNL)
In an ideal ADC, code transitions are 1 LSB apart. DNL is the
maximum deviation from this ideal value. It is often specified in
terms of resolution for which no missing codes are guaranteed.
Offset Error
The first transition should occur at a level LSB above analog
ground (38.1 μV for the 0 V to 5 V range). The offset error is
the deviation of the actual transition from that point.
Gain Error
The last transition (from 111 . . . 10 to 111 . . . 11) should
occur for an analog voltage 1 LSB below the nominal full
scale (4.999886 V for the 0 V to 5 V range). The gain error is the
deviation of the actual level of the last transition from the ideal
level after the offset is adjusted out.
Spurious-Free Dynamic Range (SFDR)
The difference, in decibels (dB), between the rms amplitude of
the input signal and the peak spurious signal.
Effective Number of Bits (ENOB)
ENOB is a measurement of the resolution with a sine wave
input. It is related to SINAD by
ENOB = (SINADdB 1.76)/6.02
and is expressed in bits.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first five harmonic
components to the rms value of a full-scale input signal and is
expressed in dB.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the actual input signal to the
rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in dB.
Signal-to-(Noise + Distortion), SINAD
SINAD is the ratio of the rms value of the actual input signal to
the rms sum of all other spectral components below the Nyquist
frequency, including harmonics but excluding dc. The value for
SINAD is expressed in dB.
Aperture Delay
Aperture delay is a measure of the acquisition performance and
is the time between the rising edge of the CNV input and when
the input signal is held for a conversion.
Transient Response
The time required for the ADC to accurately acquire its input
after a full-scale step function is applied.
相關PDF資料
PDF描述
ADM4852ARZ-REEL7 IC TXRX RS485/422 2.5MBPS 8SOIC
AD7714ARSZ-3REEL IC ADC 24BIT SIGMA-DELTA 28SSOP
SP490CN-L/TR IC TXRX RS485 FULL DUPLEX 8NSOIC
SP1485EMN-L/TR IC TXRX RS485 DIFF ESD 8SOIC
LTC1745IFW#PBF IC ADC 12BIT 25MSPS LN 48TSSOP
相關代理商/技術參數
參數描述
AD7685-C-U2 制造商:Analog Devices 功能描述:250 KSPS 16-BIT PULSAR? A/D CONVERTER IN ?SOIC - Bulk
AD7685-S-U2 制造商:Analog Devices 功能描述:250 KSPS 16-BIT PULSAR? A/D CONVERTER - Bulk
AD7685XRM-U3 制造商:Analog Devices 功能描述:A/D CONVERTER 250KSPS 16-BIT PULSAR - Bulk
AD7686 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, +/-0.65 LSB INL, 500 kSPS PulSAR Differential ADC in MSOP/QFN
AD76861 制造商:AD 制造商全稱:Analog Devices 功能描述:18-Bit, 2 MSPS PulSAR 15 mW ADC in LFCSP (QFN)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*