- 您現在的位置：買賣IC網 > PDF目錄375237 > AD7612BSTZ-RL (ANALOG DEVICES INC) 16-Bit, 750 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC PDF資料下載
參數資料
| 型號： | AD7612BSTZ-RL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 16-Bit, 750 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC |
| 中文描述： | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PQFP48 |
| 封裝： | LEAD FREE, MS-026BBC, LQFP-48 |
| 文件頁數： | 24/32頁 |
| 文件大?。?/td> | 587K |
| 代理商： | AD7612BSTZ-RL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7612
INTERFACES
DIGITAL INTERFACE
The AD7612 has a versatile digital interface that can be set up
as either a serial or a parallel interface with the host system. The
serial interface is multiplexed on the parallel data bus. The AD7612
digital interface also accommodates 2.5 V, 3.3 V, or 5 V logic. In
most applications, the OVDD supply pin is connected to the host
system interface 2.5 V to 5.25 V digital supply. Finally, by using
the OB/2C input pin, both twos complement or straight binary
coding can be used.
Rev. 0 | Page 24 of 32
Two signals, CS and RD, control the interface. When at least one of
these signals is high, the interface outputs are in high impedance.
Usually, CS allows the selection of each AD7612 in multi-circuit
applications and is held low in a single AD7612 design. RD is gen-
erally used to enable the conversion result on the data bus.
RESET
The RESET input is used to reset the AD7612. A rising edge on
RESET aborts the current conversion (if any) and tristates the
data bus. The falling edge of RESET resets the AD7612 and clears
the data bus and configuration register. See Figure 34 for the
RESET timing details.
t
9
t
8
RESET
DBUS
BUSY
CNVST
0
Figure 34. RESET Timing
PARALLEL INTERFACE
The AD7612 is configured to use the parallel interface when
SER/PAR is held low.
Master Parallel Interface
Data can be continuously read by tying CS and RD low, thus
requiring minimal microprocessor connections. However, in
this mode, the data bus is always driven and cannot be used in
shared bus applications (unless the device is held in RESET).
Figure 35 details the timing for this mode.
t
1
BUSY
BUS
PREVIOUS CONVERSION DATA
NEW DATA
CNVST
CS = RD = 0
t
10
t
4
t
11
t
3
0
Figure 35. Master Parallel Data Timing for Reading (Continuous Read)
Slave Parallel Interface
In slave parallel reading mode, the data can be read either after
each conversion, which is during the next acquisition phase, or
during the following conversion, as shown in Figure 36 and
Figure 37, respectively. When the data is read during the conver-
sion, it is recommended that it is read only during the first half
of the conversion phase. This avoids any potential feedthrough
between voltage transients on the digital interface and the most
critical analog conversion circuitry.
CURRENT
CONVERSION
t
13
t
12
BUSY
DATA
BUS
RD
CS
0
Figure 36. Slave Parallel Data Timing for Reading (Read After Convert)
PREVIOUS
CONVERSION
t
13
t
12
t
3
BUSY
DATA
BUS
CNVST,
RD
CS = 0
t
4
t
1
0
Figure 37. Slave Parallel Data Timing for Reading (Read During Convert)
相關PDF資料 |
PDF描述 |
|---|---|
| AD7622 | 16-Bit, 750 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC |
| AD7623 | 16-Bit, 750 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC |
| AD7643 | 16-Bit, 750 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC |
| AD7656 | 250 kSPS, 6-Channel,Simultaneous Sampling, Bipolar 12/14/16-Bit ADC |
| AD7656BSTZ | 250 kSPS, 6-Channel,Simultaneous Sampling, Bipolar 12/14/16-Bit ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7616BSTZ | 功能描述:16 Bit Analog to Digital Converter 16 Input 2 SAR 80-LQFP (14x14) 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:在售 位數:16 采樣率（每秒）:1M 輸入數:16 輸入類型:差分 數據接口:SPI，并聯，DSP 配置:MUX-S/H-ADC 無線電 - S/H:ADC:1:1 A/D 轉換器數:2 架構:SAR 參考類型:外部， 內部 電壓 - 電源，模擬:5V 電壓 - 電源，數字:2.3 V ~ 3.6 V 特性:同步采樣 工作溫度:-40°C ~ 125°C 封裝/外殼:80-LQFP 供應商器件封裝:80-LQFP（14x14） 標準包裝:1 |
| AD7616BSTZ-RL | 功能描述:16 Bit Analog to Digital Converter 16 Input 2 SAR 80-LQFP (14x14) 制造商:analog devices inc. 系列:- 包裝:剪切帶（CT） 零件狀態:在售 位數:16 采樣率（每秒）:1M 輸入數:16 輸入類型:差分 數據接口:SPI，并聯，DSP 配置:MUX-S/H-ADC 無線電 - S/H:ADC:1:1 A/D 轉換器數:2 架構:SAR 參考類型:外部， 內部 電壓 - 電源，模擬:5V 電壓 - 電源，數字:2.3 V ~ 3.6 V 特性:同步采樣 工作溫度:-40°C ~ 125°C 封裝/外殼:80-LQFP 供應商器件封裝:80-LQFP（14x14） 標準包裝:1 |
| AD7616-PBSTZ | 功能描述:IC DAS ADC DUAL 16BIT 16CH 80LQF 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:在售 位數:16 采樣率（每秒）:1M 輸入數:16 輸入類型:單端 數據接口:并聯 配置:MUX-ADC 無線電 - S/H:ADC:- A/D 轉換器數:2 架構:SAR 參考類型:外部， 內部 電壓 - 電源，模擬:4.75 V ~ 5.25 V 電壓 - 電源，數字:2.3 V ~ 3.6 V 特性:同步采樣 工作溫度:-40°C ~ 125°C 封裝/外殼:80-LQFP 供應商器件封裝:80-LQFP（14x14） 標準包裝:1 |
| AD7616-PBSTZ-RL | 功能描述:100KSPS 16 CH MUXED DUAL 16B SAR 制造商:analog devices inc. 系列:- 包裝:帶卷（TR） 零件狀態:在售 位數:16 采樣率（每秒）:1M 輸入數:16 輸入類型:單端 數據接口:并聯 配置:MUX-ADC 無線電 - S/H:ADC:- A/D 轉換器數:2 架構:SAR 參考類型:外部， 內部 電壓 - 電源，模擬:4.75 V ~ 5.25 V 電壓 - 電源，數字:2.3 V ~ 3.6 V 特性:同步采樣 工作溫度:-40°C ~ 125°C 封裝/外殼:80-LQFP 供應商器件封裝:80-LQFP（14x14） 標準包裝:1,000 |
| AD7617BSTZ | 功能描述:1MSPS 16 CH MUXED DUAL 14B SAR A 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:在售 位數:14 采樣率（每秒）:1M 輸入數:16 輸入類型:單端 數據接口:DSP，MICROWIRE?，并聯，QSPI?，串行，SPI? 配置:MUX-ADC 無線電 - S/H:ADC:- A/D 轉換器數:2 架構:SAR 參考類型:外部， 內部 電壓 - 電源，模擬:4.75 V ~ 5.5 V 電壓 - 電源，數字:2.3 V ~ 3.6 V 特性:同步采樣 工作溫度:-40°C ~ 125°C 封裝/外殼:80-LQFP 供應商器件封裝:80-LQFP（14x14） 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。