參數資料
型號: AD7609BSTZ
廠商: Analog Devices Inc
文件頁數: 20/36頁
文件大?。?/td> 0K
描述: IC DAS 18BIT 8CHANNEL 64-LQFP
特色產品: A/D Converters
標準包裝: 1
類型: 數據采集系統(DAS),ADC
分辨率(位): 18 b
采樣率(每秒): 200k
數據接口: DSP,MICROWIRE?,并聯,QSPI?,串行,SPI?
電壓電源: 模擬和數字
電源電壓: 2.3 V ~ 5 V,4.75 V ~ 5.25 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 64-LQFP
供應商設備封裝: 64-LQFP(10x10)
包裝: 托盤
Data Sheet
AD7609
Rev. A | Page 27 of 36
Figure 6 shows the timing diagram for reading one channel of
data, framed by the CS signal, from the AD7609 in serial mode.
The SCLK input signal provides the clock source for the serial
read operation. CS goes low to access the data from the AD7609.
The falling edge of CS takes the bus out of three-state and
clocks out the MSB of the 18-bit conversion result. This MSB
is valid on the first falling edge of the SCLK after the CS falling
edge. The subsequent 17 data bits are clocked out of the
AD7609 on the SCLK rising edge. Data is valid on the SCLK
falling edge. Eighteen clock cycles must be provided to the
AD7609 to access each conversion result.
The FRSTDATA output signal indicates when the first channel,
V1, is being read back. When the CS input is high, the FRSTDATA
output pin is in three-state. In serial mode, the falling edge of
CS takes FRSTDATA out of three-state and sets the FRSTDATA
pin high indicating that the result from V1 is available on the
DOUTA output data line. The FRSTDATA output returns to a
logic low following the 18th SCLK falling edge. If all channels
are read on DOUTB, the FRSTDATA output does not go high
when V1 is being output on this serial data output pin. It only
goes high when V1 is available on DOUTA (and this is when V5
is available on DOUTB).
READING DURING CONVERSION
Data can be read from the AD7609 while BUSY is high
and conversions are in progress. This has little effect on the
performance of the converter and allows a faster throughput
rate to be achieved. A parallel or serial read can be performed
during conversions and when oversampling may or may not
be in use. Figure 3 shows the timing diagram for reading while
BUSY is high in parallel or serial mode. Reading during conver-
sions allows the full throughput rate to be achieved when using
the serial interface with a VDRIVE of 3.3 V to 5.25 V.
Data can be read from the AD7609 at any time other than on
the falling edge of BUSY because this is when the output data
registers are updated with the new conversion data. t6, outlined
in Table 3, should be observed in this condition.
V1
V4
V2
V3
V5
V8
V6
V7
SCLK
DOUTA
DOUTB
CS
72
09760-
041
Figure 44. AD7609 Serial Interface with Two DOUT Lines
相關PDF資料
PDF描述
MS3126E14-12PW CONN PLUG 12POS STRAIGHT W/PINS
LTC1290CCSW#PBF IC DATA ACQ SYS 12BIT 20-SOIC
VI-B4K-MY-S CONVERTER MOD DC/DC 40V 50W
V110A24M300BL2 CONVERTER MOD DC/DC 24V 300W
AD7891BSZ-1 IC DAS 12BIT 8CH 44-MQFP
相關代理商/技術參數
參數描述
AD7609BSTZ-RL 功能描述:IC DAS W/ADC 18BIT 8CH 64LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統(DAS) 分辨率(位):16 b 采樣率(每秒):21.94k 數據接口:MICROWIRE?,QSPI?,串行,SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP(6x6) 包裝:托盤
AD760AN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Digital-to-Analog Converter
AD760AP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Digital-to-Analog Converter
AD760AQ 功能描述:IC DAC 16BIT W/AMP SRL 28-CDIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:DACPORT® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散(最大):- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP,8-MSOP(0.118",3.00mm 寬) 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓,單極 采樣率(每秒):* 產品目錄頁面:1398 (CN2011-ZH PDF)
AD760SQ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Digital-to-Analog Converter