- 您現在的位置：買賣IC網 > PDF目錄165343 > AD7457BRT-REEL7 (ANALOG DEVICES INC) Low Power, Pseudo Differential, 100 kSPS 12-Bit ADC in an 8-Lead SOT-23 PDF資料下載
參數資料
| 型號： | AD7457BRT-REEL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | Low Power, Pseudo Differential, 100 kSPS 12-Bit ADC in an 8-Lead SOT-23 |
| 中文描述： | 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8 |
| 封裝： | MO-178BA, SOT-23, 8 PIN |
| 文件頁數： | 8/20頁 |
| 文件大小： | 532K |
| 代理商： | AD7457BRT-REEL7 |
AD7457
Rev. A | Page 16 of 20
APPLICATION HINTS
GROUNDING AND LAYOUT
The printed circuit board that houses the AD7457 should be
designed so that the analog and digital sections are separated
and confined to certain areas of the board. This facilitates the
use of ground planes that can be easily separated. A minimum
etch technique is generally best for ground planes, because it
gives the best shielding. Digital and analog ground planes
should be joined in only one place, and the connection should
be a star ground point established as close as possible to the
GND pin on the AD7457.
Avoid running digital lines under the device, because this
couples noise onto the die. The analog ground plane should be
allowed to run under the AD7457 to avoid noise coupling. The
power supply lines to the AD7457 should use as large a trace as
possible to provide low impedance paths and reduce the effects
of glitches on the power supply line. Fast switching signals,
such as clocks, should be shielded with digital ground to avoid
radiating noise to other sections of the board, and clock signals
should never run near the analog inputs. Avoid crossover of
digital and analog signals. Traces on opposite sides of the board
should run at right angles to each other. This reduces the effects
of feed through the board. A micro strip technique is the best,
but is not always possible with a double-sided board.
In this technique, the component side of the board is dedicated
to ground planes, while signals are placed on the solder side.
Good decoupling is also important. All analog supplies should
be decoupled with 10 F tantalum capacitors in parallel with
0.1 F capacitors to GND. To achieve the best from these
decoupling components, place them as close as possible to
the device.
相關PDF資料 |
PDF描述 |
|---|---|
| AD745AN | Ultralow Noise, High Speed, BiFET Op Amp |
| AD745JN | Ultralow Noise, High Speed, BiFET Op Amp |
| AD7466BRM | 1.8 V, Micro-Power, 8/10/12-Bit ADCs in 6 Lead SOT-23 |
| AD7466BRT | 1.8 V, Micro-Power, 8/10/12-Bit ADCs in 6 Lead SOT-23 |
| AD7467BRT | 1.8 V, Micro-Power, 8/10/12-Bit ADCs in 6 Lead SOT-23 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7457BRTZ-R2 | 制造商:Analog Devices 功能描述: |
| AD7457BRTZ-REEL | 制造商:Analog Devices 功能描述: |
| AD7457BRTZ-REEL7 | 功能描述:IC ADC 12BIT PSEUDO-DIFF SOT23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD745AN | 制造商:AD 制造商全稱:Analog Devices 功能描述:Ultralow Noise, High Speed, BiFET Op Amp |
| AD745AQ | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。