參數資料
型號： AD7327BRUZ-REEL7
廠商： Analog Devices Inc
文件頁數： 27/37頁
文件大?。?/td> 0K
描述： IC ADC 12BIT+ SAR 8CHAN 20TSSOP
標準包裝： 1,000
位數： 12
采樣率（每秒）： 500k
數據接口： DSP，MICROWIRE?，QSPI?，串行，SPI?
轉換器數目： 1
功率耗散（最大）： 17mW
電壓電源： 雙 ±
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 20-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 20-TSSOP
包裝： 帶卷 (TR)
輸入數目和類型： 8 個單端，單極；8 個單端，雙極；4 個差分，單極；4 個差分，雙極
配用： EVAL-AD7327CBZ-ND - BOARD EVALUATION FOR AD7327
AD7327
Rev. B | Page 32 of 36
MICROPROCESSOR INTERFACING
The serial interface on the AD7327 allows the part to be directly
connected to a range of different microprocessors. This section
explains how to interface the AD7327 with some common
microcontroller and DSP serial interface protocols.
The ADSP-21xx family of DSPs interface directly to the AD7327
without requiring glue logic. The VDRIVE pin of the AD7327 takes
the same supply voltage as that of the ADSP-21xx. This allows
the ADC to operate at a higher supply voltage than its serial
interface. The SPORT0 on the ADSP-21xx should be configured
as shown in Table 14.
Table 14. SPORT0 Control Register Setup
Setting
Description
TFSW = RFSW = 1
Alternative framing
INVRFS = INVTFS = 1
Active low frame signal
DTYPE = 00
Right justify data
SLEN = 1111
16-bit data-word
ISCLK = 1
Internal serial clock
TFSR = RFSR = 1
Frame every word
IRFS = 0
ITFS = 1
The connection diagram is shown in Figure 54. The ADSP-21xx
has TFS0 and RFS0 tied together. TFS0 is set as an output, and
RFS0 is set as an input. The DSP operates in alternative framing
mode, and the SPORT0 control register is set up as described in
Table 14. The frame synchronization signal generated on the TFS
is tied to CS, and, as with all signal processing applications, requires
equidistant sampling. However, as in this example, the timer
interrupt is used to control the sampling rate of the ADC, and
under certain conditions, equidistant sampling cannot be achieved.
AD73271
ADSP-21xx1
SCLK
SCLK0
CS
TFS0
RFS0
DOUT
DIN
DT0
DR0
VDD
VDRIVE
1ADDITIONAL PINS OMITTED FOR CLARITY.
05401-
037
Figure 54. Interfacing the AD7327 to the ADSP-21xx
The timer registers are loaded with a value that provides an
interrupt at the required sampling interval. When an interrupt
is received, a value is transmitted with TFS/DT (ADC control
word). The TFS is used to control the RFS, and hence the
reading of data.
The frequency of the serial clock is set in the SCLKDIV register.
When the instruction to transmit with TFS is given (AX0 =
TX0), the state of the serial clock is checked. The DSP waits
until the SCLK has gone high, low, and high again before
starting the transmission. If the timer and SCLK are chosen so
that the instruction to transmit occurs on or near the rising
edge of SCLK, data can be transmitted immediately or at the
next clock edge.
For example, the ADSP-2111 has a master clock frequency of
16 MHz. If the SCLKDIV register is loaded with the value 3, an
SCLK of 2 MHz is obtained, and eight master clock periods elapse
for every one SCLK period. If the timer registers are loaded with
the value 803, 100.5 SCLKs occur between interrupts and, sub-
sequently, between transmit instructions. This situation leads to
nonequidistant sampling because the transmit instruction occurs
on an SCLK edge. If the number of SCLKs between interrupts is
an integer of N, equidistant sampling is implemented by the DSP.
The ADSP-BF53x family of DSPs interfaces directly to the
AD7327 without requiring glue logic, as shown in Figure 55.
The SPORT0 Receive Configuration 1 register should be set up
as outlined in Table 15.
AD73271
ADSP-BF53x1
VDD
VDRIVE
SCLK
RSCLK0
DIN
DT0
DOUT
DR0
CS
RFS0
1ADDITIONAL PINS OMITTED FOR CLARITY.
05401-
038
Figure 55. Interfacing the AD7327 to the ADSP-BF53x
Table 15. SPORT0 Receive Configuration 1 Register
Setting
Description
RCKFE = 1
Sample data with falling edge of RSCLK
LRFS = 1
Active low frame signal
RFSR = 1
Frame every word
IRFS = 1
Internal RFS used
RLSBIT = 0
Receive MSB first
RDTYPE = 00
Zero fill
IRCLK = 1
Internal receive clock
RSPEN = 1
Receive enable
SLEN = 1111
16-bit data-word
TFSR = RFSR = 1
相關PDF資料
PDF描述
AD7328BRUZ-REEL IC ADC 12BIT+SAR 8CHAN 20-TSSOP
AD7329BRUZ-REEL7 IC ADC 12BIT+SAR 8CHAN 24-TSSOP
AD73311ARSZ IC ANALOG FRONT END 20-SSOP
AD73322LARUZ-REEL IC PROCESSOR FRONTEND DL 28TSSOP
AD73322LYRZ IC ANALOG FRONT END DUAL 28-SOIC
相關代理商/技術參數
參數描述
AD7328 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Channel, Software-Selectable True Bipolar Input, 12-Bit Plus Sign ADC
AD7328BRUZ 功能描述:IC ADC 12BIT+ SAR 8CHAN 20TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:iCMOS® 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
AD7328BRUZ 制造商:Analog Devices 功能描述:A/D Converter (A-D) IC
AD7328BRUZ-REEL 功能描述:IC ADC 12BIT+SAR 8CHAN 20-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:iCMOS® 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
AD7328BRUZ-REEL7 功能描述:IC ADC 12BIT+ SAR 8CHAN 20TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:iCMOS® 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*