參數資料
型號: AD7306JRZ-REEL
廠商: Analog Devices Inc
文件頁數: 8/8頁
文件大?。?/td> 0K
描述: IC TXRX RS232/RS422 5V 24-SOIC
標準包裝: 1,000
類型: 收發器
驅動器/接收器數: 3/3
規程: RS232
電源電壓: 4.75 V ~ 5.25 V
安裝類型: 表面貼裝
封裝/外殼: 24-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 24-SOIC W
包裝: 帶卷 (TR)
AD7306
–8–
REV. B
C1624a–2–8/94
PRINTED
IN
U.S.A.
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
Single-Ended Data Transmission
Single-ended interfaces are used for low speed, short distance
communications such as from a computer terminal to a printer.
A single line is used to carry the signal. Various standards have
been developed to standardize the communication link, the most
popular of these being the RS-232. The RS-232 standard was
introduced in 1962 by the EIA and has been widely used
throughout the industry. The standard has been revised several
times, and the current revision is known as EIA-232E. The
RS-232 standard is suitable for single-ended data transmission
at relatively slow data rates over short distances. A typical
RS-232 interface is shown in Figure 14.
RS-232 CHANNEL
DATA
IN
DATA
OUT
RX
TX
Figure 14. Single-Ended RS-232 Interface
Differential Data Transmission
When transmitting at high data rates, over long distances and
through noisy environments, single-ended data transmission is
often inadequate. In this type of application, differential data
transmission offers superior performance. Differential transmis-
sion uses two signal lines to transmit data. It rejects ground
shifts and is insensitive to noise signals which appear as com-
mon mode voltages on the transmission lines. To accommodate
faster data communication, the differential RS-422 standard was
developed. Therefore, it can be used to reliably transmit data at
higher speeds and over longer distances than single-ended trans-
mission. A typical RS-422 interface is shown in Figure 15.
RS-422 CHANNEL
DATA
IN
DATA
OUT
RX
TX
Figure 15. Differential RS-422 Interface
Table I. Comparison of RS-232 and RS-422 Interface Standards
Specification
EIA-232E
RS-422
Transmission Type
Single-Ended
Differential
Maximum Data Rate
20 kB/s
10 MB/s
Maximum Cable Length
Load Dependent
4000 ft.
Minimum Driver Output Voltage
±5 V
±1.5 V
Slew Rate
30 V/
s max
Receiver Input Resistance
3 k
to 7 k
4 k
min
Receiver Input Sensitivity
±3 V
±200 mV
Receiver Input Voltage Range
±15 V
±7 V
No. of Drivers per Line
1
No. of Receivers per Line
1
10
24-Lead SOIC (R-24)
24
13
12
1
0.6141 (15.60)
0.5985 (15.20)
0.4193
(10.65)
0.3937
(10.00)
0.2992
(7.60)
0.2914
(7.40)
PIN 1
SEATING
PLANE
0.0118 (0.30)
0.0040 (0.10)
0.0192 (0.49)
0.0138 (0.35)
0.1043 (2.65)
0.0926 (2.35)
0.0500
(1.27)
BSC
0.0125 (0.32)
0.0091 (0.23)
0.0500 (1.27)
0.0157 (0.40)
8
°
0
°
0.0291 (0.74)
0.0098 (0.25)
x 45
°
24-Lead Pin Plastic DIP (N-24)
0.260
± 0.001
(6.61
± 0.03)
0
° - 15°
0.11 (2.79)
0.09 (2.28)
SEATING
PLANE
1.228 (31.19)
1.226 (31.14)
0.02 (0.5)
0.016 (0.41)
0.07(1.78)
0.05 (1.27)
0.130 (3.30)
0.128 (3.25)
0.32 (8.128)
0.30 (7.62)
0.011 (0.28)
0.009 (0.23)
NOTES
1.
2.
LEAD NO. 1 IDENTIFIED BY DOT OR NOTCH.
PLASTIC LEADS WILL BE EITHER SOLDER DIPPED OR TIN LEAD PLATED
IN ACCORDANCE WITH MIL-M-385 10 REQUIREMENTS.
相關PDF資料
PDF描述
IDT72825LB10PF8 IC FIFO SYNC DL 1024X18 128TQFP
XRT7296IWTR IC LINE TX DS3/STS-1 E3 28SOJ
VE-25H-IU-F2 CONVERTER MOD DC/DC 52V 200W
MS27484T14F35SC CONN PLUG 37POS STRAIGHT W/SCKT
IDT72V831L20TF IC SYNC FIFO 2048X9 20NS 64QFP
相關代理商/技術參數
參數描述
AD730JR-1 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Miscellaneous Clock Generator
AD7312 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1/4 to 1/11 Duty VFD Controller/Driver & Standby Master/Slave
AD7312L 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1/4 to 1/11 Duty VFD Controller/Driver & Standby Master/Slave
AD7312LF 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1/4 to 1/11 Duty VFD Controller/Driver & Standby Master/Slave
AD7312Q 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1/4 to 1/11 Duty VFD Controller/Driver & Standby Master/Slave