- 您現在的位置：買賣IC網 > PDF目錄1980 > AD7170BCPZ-REEL7 (Analog Devices Inc)IC ADC 12BIT SIGMA-DELTA 10LFCSP PDF資料下載
參數資料
| 型號： | AD7170BCPZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 4/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT SIGMA-DELTA 10LFCSP |
| 標準包裝： | 1 |
| 位數： | 12 |
| 采樣率（每秒）： | 125 |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-WFDFN 裸露焊盤，CSP |
| 供應商設備封裝： | 10-LFCSP-WD（3x3） |
| 包裝： | 標準包裝 |
| 輸入數目和類型： | 2 個單端，雙極；1 個差分，雙極 |
| 產品目錄頁面： | 777 (CN2011-ZH PDF) |
| 其它名稱： | AD7170BCPZ-500RL7DKR AD7170BCPZ-500RL7DKR-ND AD7170BCPZ-REEL7DKR |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
AD7170
Data Sheet
Rev. A | Page 12 of 16
GROUNDING AND LAYOUT
Because the analog input and reference input of the ADC are
differential, most of the voltages in the analog modulator are
common-mode voltages. The excellent common-mode reject-
ion of the part removes common-mode noise on these inputs.
The digital filter provides rejection of broadband noise on the
power supply, except at integer multiples of the modulator
sampling frequency. The digital filter also removes noise from
the analog and reference inputs provided that these noise sources
do not saturate the analog modulator. As a result, the AD7170
is more immune to noise interference than conventional high
resolution converters. However, because the noise levels from
the AD7170 are so low, care must be taken with regard to
grounding and layout.
The printed circuit board that houses the AD7170 should be
designed such that the analog and digital sections are separated
and confined to certain areas of the board. A minimum etch
technique is generally best for ground planes because it gives
the best shielding.
It is recommended that the GND pin of the AD7170 be tied to
the analog ground (AGND) plane of the system. In any layout,
it is important that the user pay attention to the flow of currents
in the system and ensure that the return paths for all currents
are as close as possible to the paths the currents took to reach
their destinations. Avoid forcing digital currents to flow through
the AGND sections of the layout.
The ground plane of the AD7170 should be allowed to run
under the AD7170 to prevent noise coupling. The power supply
lines to the AD7170 should use as wide a trace as possible to
provide low impedance paths and reduce the effects of glitches
on the power supply line. Fast switching signals such as clocks
should be shielded with digital ground to avoid radiating noise
to other sections of the board, and clock signals should never be
run near the analog inputs. Avoid crossover of digital and
analog signals. Traces on opposite sides of the board should run
at right angles to each other. This reduces the effects of
feedthrough through the board. A microstrip technique is by far
the best, but it is not always possible with a double-sided board.
In this technique, the component side of the board is dedicated
to ground planes, while signals are placed on the solder side.
Good decoupling is important when using high resolution ADCs.
VDD should be decoupled with 10 μF tantalum capacitors in
parallel with 0.1 μF capacitors to GND, with the system’s analog
ground to digital ground (DGND) connection being close to
the AD7170. To achieve the best results from these decoupling
components, they should be placed as close as possible to the
device, ideally right up against the device. All logic chips should
be decoupled with 0.1 μF ceramic capacitors to DGND.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7171BCPZ-REEL7 | IC ADC 16BIT SER 125HZ 10LFCSP |
| AD7190BRUZ-REEL | IC ADC 2CH 24BIT W/PGA 24TSSOP |
| AD7191BRUZ | IC ADC 2CH 24B SD 24TSSOP |
| AD7192BRUZ | IC ADC 24BIT 2CH W/PGA 24-TSSOP |
| AD7193BCPZ | IC ADC 24BIT SPI 4.8KHZ 32LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7171 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit Low Power Sigma-Delta ADC |
| AD7171BCPZ-500RL7 | 功能描述:IC ADC 16BIT SER 125HZ 10LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7171BCPZ-REEL7 | 功能描述:IC ADC 16BIT SER 125HZ 10LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7172-2BRUZ | 功能描述:24 Bit Analog to Digital Converter 2, 4 Input 1 Sigma-Delta 24-TSSOP 制造商:analog devices inc. 系列:- 包裝:管件 零件狀態:有效 位數:24 采樣率（每秒）:31.25k 輸入數:2，4 輸入類型:差分，單端 數據接口:SPI，DSP 配置:MUX-ADC 無線電 - S/H:ADC:- A/D 轉換器數:1 架構:三角積分 參考類型:外部， 內部 電壓 - 電源，模擬:2 V ~ 5.5 V 電壓 - 電源，數字:2 V ~ 5.5 V 特性:- 工作溫度:-40°C ~ 105°C 封裝/外殼:24-TSSOP（0.173"，4.40mm 寬） 供應商器件封裝:24-TSSOP 標準包裝:62 |
| AD7172-2BRUZ-RL | 功能描述:24 Bit Analog to Digital Converter 2, 4 Input 1 Sigma-Delta 24-TSSOP 制造商:analog devices inc. 系列:- 包裝:帶卷（TR） 零件狀態:有效 位數:24 采樣率（每秒）:31.25k 輸入數:2，4 輸入類型:差分，單端 數據接口:SPI，DSP 配置:MUX-ADC 無線電 - S/H:ADC:- A/D 轉換器數:1 架構:三角積分 參考類型:外部， 內部 電壓 - 電源，模擬:2 V ~ 5.5 V 電壓 - 電源，數字:2 V ~ 5.5 V 特性:- 工作溫度:-40°C ~ 105°C 封裝/外殼:24-TSSOP（0.173"，4.40mm 寬） 供應商器件封裝:24-TSSOP 標準包裝:2,500 |
發布緊急采購，3分鐘左右您將得到回復。