參數資料
型號: AD5749ACPZ-RL7
廠商: Analog Devices Inc
文件頁數: 7/28頁
文件大?。?/td> 0K
描述: IC CURRENT OUT DVR 32-LFCSP
標準包裝: 1
放大器類型: 儀表
電路數: 1
電流 - 電源: 5.2mA
電流 - 輸出 / 通道: 24mA
電壓 - 電源,單路/雙路(±): 10.8 V ~ 55 V
工作溫度: -40°C ~ 105°C
安裝類型: 表面貼裝
封裝/外殼: 32-VFQFN 裸露焊盤,CSP
供應商設備封裝: 32-LFCSP-VQ(5x5)
包裝: 標準包裝
其它名稱: AD5749ACPZ-RL7DKR
Data Sheet
AD5749
Rev. B | Page 15 of 28
TERMINOLOGY
Total Unadjusted Error (TUE)
TUE is a measure of the output error taking all the various
errors into account: INL error, offset error, gain error, and
output drift over supplies, temperature, and time. TUE is
expressed as a percentage of full-scale range (% FSR).
Relative Accuracy or Integral Nonlinearity (INL)
INL is a measure of the maximum deviation, in % FSR, from a
straight line passing through the endpoints of the output driver
transfer function. A typical INL vs. input voltage plot is shown
Full-Scale Error
Full-scale error is the deviation of the actual full-scale analog
output from the ideal full-scale output. Full-scale error is
expressed as a percentage of full-scale range (% FSR).
Full-Scale TC
Full-scale TC is a measure of the change in the full-scale error
with a change in temperature. It is expressed in ppm FSR/°C.
Gain Error
Gain error is a measure of the span error of the output. It is the
deviation in slope of the output transfer characteristic from the
ideal expressed in % FSR. A plot of gain error vs. temperature is
Gain Error TC
Gain error TC is a measure of the change in gain error with
changes in temperature. Gain error TC is expressed in ppm
FSR/°C.
Zero-Scale Error
Zero-scale error is the deviation of the actual zero-scale analog
output from the ideal zero-scale output. Zero-scale error is
expressed in millivolts (mV).
Zero-Scale TC
Zero-scale TC is a measure of the change in zero-scale error
with a change in temperature. Zero-scale error TC is expressed
in ppm FSR/°C.
Offset Error
Offset error is a measurement of the difference between the
actual VOUT and the ideal VOUT expressed in millivolts (mV)
in the linear region of the transfer function. It can be negative
or positive.
Output Voltage Settling Time
Output voltage settling time is the amount of time it takes for
the output to settle to a specified level for a half-scale input change.
Slew Rate
The slew rate of a device is a limitation in the rate of change
of the output voltage. The output slewing speed is usually
limited by the slew rate of the amplifier used at its output. Slew
rate is measured from 10% to 90% of the output signal and is
expressed in V/μs.
Current Loop Voltage Compliance
Current loop voltage compliance is the maximum voltage at
the IOUT pin for which the output current is equal to the
programmed value.
Power-On Glitch Energy
Power-on glitch energy is the impulse injected into the analog
output when the AD5749 is powered on. It is specified as the
area of the glitch in nV-sec.
Power Supply Rejection Ratio (PSRR)
PSRR indicates how the output is affected by changes in the
power supply voltage.
相關PDF資料
PDF描述
NPPC192KFMS-RC CONN FMALE 38POS DL .1" GOLD SMD
2-1879208-5 RES 100 OHM 1/16W 0.1% 0402
0001.2522 FUSE 630MA 250V 6.3X32 T-LAG
0001.2523 FUSE 800MA 250V 6.3X32 T-LAG
0001.2524 FUSE 1A 250V 6.3X32 T-LAG
相關代理商/技術參數
參數描述
AD574A 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete 12-Bit A/D Converter
AD574AJ 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete 12-Bit A/D Converter
AD574AJD 功能描述:IC ADC 12BIT W/REF 28-CDIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率(每秒):83k 數據接口:串行,并聯 轉換器數目:1 功率耗散(最大):95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP(0.600",15.24mm) 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端,雙極
AD574AJD/+ 制造商:Analog Devices 功能描述:ADC SGL SAR 12-BIT PARALLEL 28PIN SBDIP - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:IC, MONO 12-BIT A/D CONV - Bulk