- 您現在的位置：買賣IC網 > PDF目錄1978 > AD5380BSTZ-3 (Analog Devices Inc)IC DAC 14BIT 40CHAN 3V 100LQFP PDF資料下載
參數資料
| 型號： | AD5380BSTZ-3 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 16/40頁 |
| 文件大小： | 0K |
| 描述： | IC DAC 14BIT 40CHAN 3V 100LQFP |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 產品變化通告： | Redesign Change 28/Oct/2011 |
| 設計資源： | 40 Channels of Programmable Voltage with Excellent Temperature Drift Performance Using AD5380 (CN0007) Output Channel Monitoring Using AD5380 (CN0008) |
| 標準包裝： | 1 |
| 設置時間： | 6µs |
| 位數： | 14 |
| 數據接口： | I²C，并聯，串行 |
| 轉換器數目： | 40 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 125mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LQFP |
| 供應商設備封裝： | 100-LQFP（14x14） |
| 包裝： | 托盤 |
| 輸出數目和類型： | 40 電壓，單極 |
| 采樣率（每秒）： | 125k |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
Data Sheet
AD5380
Rev. C | Page 23 of 40
Table 15. Control Register Contents
MSB
LSB
CR13
CR12
CR11
CR10
CR9
CR8
CR7
CR6
CR5
CR4
CR3
CR2
CR1
CR0
Control Register Write/Read
REG1 = REG0 = 0, A5 to A0 = 001100, R/W status determines
if the operation is a write (R/W = 0) or a read (R/W = 1). DB13
to DB0 contains the control register data.
Control Register Contents
CR13: Power-Down Status. This bit is used to configure the
output amplifier state in power down.
CR13 = 1. Amplifier output is high impedance (default on
power-up).
CR13 = 0. Amplifier output is 100 k to ground.
CR12: REF Select. This bit selects the operating internal
reference for the AD5380. CR12 is programmed as follows:
CR12 = 1: Internal reference is 2.5 V (AD5380-5 default),
the recommended operating reference for AD5380-5.
CR12 = 0: Internal reference is 1.25 V (AD5380-3 default),
the recommended operating reference for AD5380-3.
CR11: Current Boost Control. This bit is used to boost the
current in the output amplifier, thereby altering its slew rate.
This bit is configured as follows:
CR11 = 1: Boost Mode On. This maximizes the bias current
in the output amplifier, optimizing its slew rate but increasing
the power dissipation.
CR11 = 0: Boost Mode Off (default on power-up). This
reduces the bias current in the output amplifier and reduces
the overall power consumption.
CR10: Internal/External Reference. This bit determines if the
DAC uses its internal reference or an externally applied
reference.
CR10 = 1: Internal Reference Enabled. The reference output
depends on data loaded to CR12.
CR10 = 0: External Reference Selected (default on power-up).
CR9: Channel Monitor Enable (see Channel Monitor Function).
CR9 = 1: Monitor Enabled. This enables the channel monitor
function. After a write to the monitor channel in the SFR
register, the selected channel output is routed to the
MON_OUT pin. VOUT39 operates as the MON_OUT pin.
CR9 = 0: Monitor Disabled (default on power-up). When the
monitor is disabled, the MON_OUT pin assumes its normal
DAC output function.
CR8: Thermal Monitor Function. This function is used to
monitor the AD5380’s internal die temperature when enabled.
The thermal monitor powers down the output amplifiers when
the temperature exceeds 130°C. This function can be used to
protect the device in cases where power dissipation may be
exceeded if a number of output channels are simultaneously
short-circuited. A soft power-up will re-enable the output
amplifiers if the die temperature has dropped below 130°C.
CR8 = 1: Thermal Monitor Enabled.
CR8 = 0: Thermal Monitor Disabled (default on power-up).
CR7: Don’t Care.
CR6 to CR2: Toggle Function Enable. This function allows the
user to toggle the output between two codes loaded to the A
and B registers for each DAC. Control Register Bits CR6 to CR2
are used to enable individual groups of eight channels for
operation in toggle mode. A Logic 1 written to any bit enables
a group of channels; a Logic 0 disables a group. LDAC is used to
toggle between the two registers. Table 16 shows the decoding
for toggle mode operation. For example, CR6 controls Group w,
which contains Channel 32 to Channel 39, CR6 = 1 enables
these channels.
CR1 and CR0: Don’t Care.
Table 16.
CR Bit
Group
Channels
CR6
4
32–39
CR5
3
24–31
CR4
2
16–23
CR3
1
8–15
CR2
0
0–7
Channel Monitor Function
REG1 = REG0 = 0, A5 to A0 = 001010
DB13 to DB8 = Contain data to address the monitored channel.
A channel monitor function is provided on the AD5380. This
feature, which consists of a multiplexer addressed via the inter-
face, allows any channel output to be routed to the MON_OUT
pin for monitoring using an external ADC. In channel monitor
mode, VOUT39 becomes the MON_OUT pin, to which all
monitored pins are routed. The channel monitor function must
be enabled in the control register before any channels are routed
to MON_OUT. On the AD5380, DB13 to DB8 contain the
channel address for the monitored channel. Selecting Channel
Address 63 three-states MON_OUT.
相關PDF資料 |
PDF描述 |
|---|---|
| AD5381BSTZ-5 | IC DAC 12BIT 40CH 5V 100-LQFP |
| AD5382BSTZ-3 | IC DAC 14BIT 32CHAN 3V 100LQFP |
| AD5390BCPZ-5 | IC DAC 14BIT 16CHAN 5V 64LFCSP |
| AD5398ABCBZ-REEL | IC DAC 10BIT CURRENT-SINK 9WLCSP |
| AD5405YCPZ-REEL7 | IC DAC DUAL 12BIT MULT 40LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5380BSTZ-5 | 功能描述:IC DAC 14BIT 12C 40CH 5V 100LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
| ad5381bst-3 | 制造商:Rochester Electronics LLC 功能描述:32/40-CHANNEL 3V/5V SINGLE SUPPLY 12/14-BIT VOUT DAC - Bulk 制造商:Analog Devices 功能描述: |
| AD5381BST-3-REEL | 制造商:Analog Devices 功能描述:DAC 40-CH Resistor-String 12-bit 100-Pin LQFP T/R |
| AD5381BST-5 | 制造商:Analog Devices 功能描述:DAC 40-CH Resistor-String 12-bit 100-Pin LQFP |
| AD5381BST-5-REEL | 制造商:Analog Devices 功能描述:DAC 40-CH Resistor-String 12-bit 100-Pin LQFP T/R |
發布緊急采購，3分鐘左右您將得到回復。