- 您現在的位置：買賣IC網 > PDF目錄9281 > AD5235BRUZ25-RL7 (Analog Devices Inc)IC DGTL POT DUAL 1024POS 16TSSOP PDF資料下載
參數資料
| 型號： | AD5235BRUZ25-RL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 16/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DGTL POT DUAL 1024POS 16TSSOP |
| 產品變化通告： | Metal Edit Change 03/Feb/2012 |
| 標準包裝： | 1,000 |
| 接片： | 1024 |
| 電阻（歐姆）： | 25k |
| 電路數： | 2 |
| 溫度系數： | 標準值 35 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 4 線 SPI（芯片選擇） |
| 電源電壓： | 3 V ~ 5.5 V，±2.25 V ~ 2.75 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Data Sheet
AD5235
Rev. F | Page 23 of 32
Because the AD5235 can also be supplied by dual supplies, the
general equation defining the output voltage at VW with respect
to ground for any given input voltages applied to Terminal A
and Terminal B is
B
AB
W
V
D
V
+
×
=
1024
)
(
(3)
Equation 3 assumes that VW is buffered so that the effect of wiper
resistance is minimized. Operation of the digital potentiometer in
divider mode results in more accurate operation over temperature.
Here, the output voltage is dependent on the ratio of the internal
resistors and not the absolute value; therefore, the drift improves
to 15 ppm/°C. There is no voltage polarity restriction between
Terminal A, Terminal B, and Terminal W as long as the
terminal voltage (VTERM) stays within VSS < VTERM < VDD.
PROGRAMMING EXAMPLES
The following programming examples illustrate a typical sequence
of events for various features of the AD5235. See Table 7 for the
instructions and data-word format. The instruction numbers,
addresses, and data appearing at the SDI and SDO pins are in
hexadecimal format.
Table 14. Scratchpad Programming
SDI
SDO
Action
0xB00100
0xXXXXXX
Writes Data 0x100 into RDAC1 register,
Wiper W1 moves to 1/4 full-scale
position.
0xB10200
0xB00100
Loads Data 0x200 into RDAC2 register,
Wiper W2 moves to 1/2 full-scale
position.
Table 15. Incrementing RDAC Followed by Storing the
Wiper Setting to EEMEM
SDI
SDO
Action
0xB00100
0xXXXXXX
Writes Data 0x100 into RDAC1
register, Wiper W1 moves to 1/4 full-
scale position.
0xE0XXXX
0xB00100
Increments RDAC1 register by one to
0x101.
0xE0XXXX
Increments RDAC1 register by one to
0x102. Continue until desired wiper
position is reached.
0x20XXXX
0xXXXXXX
Stores RDAC2 register data into
EEMEM1. Optionally, tie WP to GND to
protect EEMEM values.
The EEMEM values for the RDACs can be restored by power-
on, by strobing the PR pin, or by the two commands shown in
Table 16. Restoring the EEMEM Values to RDAC Registers
SDI
SDO
Action
0x10XXXX
0xXXXXXX
Restores the EEMEM1 value to the
RDAC1 register.
Table 17. Using Left-Shift by One to Increment 6 dB Steps
SDI
SDO
Action
0xC0XXXX
0xXXXXXX
Moves Wiper 1 to double the
present data contained in the
RDAC1 register.
0xC1XXXX
0xC0XXXX
Moves Wiper 2 to double the
present data contained in the
RDAC2 register.
Table 18. Storing Additional User Data in EEMEM
SDI
SDO
Action
0x32AAAA
0xXXXXXX
Stores Data 0xAAAA in the extra
EEMEM location USER1. (Allowable to
address in 13 locations with a
maximum of 16 bits of data.)
0x335555
0x32AAAA
Stores Data 0x5555 in the extra
EEMEM location USER2. (Allowable to
address in 13 locations with a
maximum of 16 bits of data.)
Table 19. Reading Back Data from Memory Locations
SDI
SDO
Action
0x92XXXX
0xXXXXXX
Prepares data read from USER1
EEMEM location.
0x00XXXX
0x92AAAA
NOP Instruction 0 sends a 24-bit word
out of SDO, where the last 16 bits
contain the contents in USER1 EEMEM
location.
Table 20. Reading Back Wiper Settings
SDI
SDO
Action
0xB00200
0xXXXXXX
Writes RDAC1 to midscale.
0xC0XXXX
0xB00200
Doubles RDAC1 from midscale to full
scale.
0xA0XXXX
0xC0XXXX
Prepares reading wiper setting from
RDAC1 register.
0xXXXXXX
0xA003FF
Reads back full-scale value from SDO.
EVAL-AD5235SDZ EVALUATION KIT
Analog Devices, Inc., offers a user-friendly EVAL-AD5235SDZ
evaluation kit that can be controlled by a PC in conjunction
with the SDP platform. The driving program is self-contained;
no programming languages or skills are needed.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-2TP-MW | CONVERTER MOD DC/DC 13.8V 100W |
| DS1135Z-12+T&R | IC DELAY LINE 12NS 8-SOIC |
| DS1135Z-20+T&R | IC DELAY LINE 20NS 8-SOIC |
| DS1135Z-10+T&R | IC DELAY LINE 10NS 8-SOIC |
| DS1100LU-25+T | IC DELAY LINE 5TAP 25NS 8-USOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5235-EP | 制造商:AD 制造商全稱:Analog Devices 功能描述:Nonvolatile Memory, Dual 1024-Position Digital Potentiometer |
| AD5235EVAL | 制造商:Analog Devices 功能描述:DUAL 10BIT SPI EVAL BOARD - Bulk |
| AD5235EVAL25 | 制造商:Analog Devices 功能描述:Evaluation Board For 1024-Position Digital Potentiometer 制造商:Analog Devices 功能描述:DUAL 10BIT SPI EVAL BOARD - Bulk |
| AD5235EVAL250 | 制造商:Analog Devices 功能描述:DUAL 10BIT SPI EVAL BOARD - Bulk |
| AD523BS | 制造商:POP 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。