- 您現在的位置：買賣IC網 > PDF目錄1889 > AD2S1200WSTZ (Analog Devices Inc)IC R/D CONV W/REF OSCIL 44-LQFP PDF資料下載
參數資料
| 型號： | AD2S1200WSTZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC R/D CONV W/REF OSCIL 44-LQFP |
| 標準包裝： | 1 |
| 類型： | R/D 轉換器 |
| 分辨率（位）： | 12 b |
| 數據接口： | 串行，并聯 |
| 電壓電源： | 模擬和數字 |
| 電源電壓： | 5V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LQFP |
| 供應商設備封裝： | 44-LQFP（7x7） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 790 (CN2011-ZH PDF) |
| 配用： | EVAL-AD2S1200CBZ-ND - BOARD EVAL FOR AD2S1200 |
AD2S1200
Rev. 0 | Page 17 of 24
Synthetic Reference Generation
When a resolver undergoes a high rotation rate, the RDC tends
to act as an electric motor and produces speed voltages, along
with the ideal Sin and Cos outputs. These speed voltages are in
quadrature to the main signal waveform. Moreover, nonzero
resistance in the resolver windings causes a non-zero phase shift
between the reference input and the Sin and Cos outputs. The
combination of speed voltages and phase shift causes a tracking
error in the RDC that is approximated by
Frequency
Reference
Rate
Rotation
Shift
Phase
Error
×
=
To compensate for the described phase error between the
resolver reference excitation and the Sin/Cos signals, an internal
synthetic reference signal is generated in phase with the refer-
ence frequency carrier. The synthetic reference is derived using
the internally filtered Sin and Cos signals. It is generated by
determining the zero crossing of either the Sin or Cos (which-
ever signal is larger, to improve phase accuracy) and evaluating
the phase of the resolver reference excitation. The synthetic
reference reduces the phase shift between the reference and
Sin/Cos inputs to less than 10°, and will operate for phase shifts
of ±45°.
SUPPLY SEQUENCING AND RESET
The AD2S1200 requires an external reset signal to hold the
RESET input low until VDD is within the specified operating
range of 4.5 V to 5.5 V.
The RESET pin must be held low for a minimum of 10 s after
RESET signal to the AD2S1200 initializes the output position to
a value of 0x000 (degrees output through the parallel, serial, and
encoder interfaces) and causes LOS to be indicated (LOT and
DOS pins pulled low) as shown in Figure 10.
Failure to apply the above (correct) power-up/reset sequence
can result in an incorrect position indication.
After a rising edge on the RESET input, the device must be
circuitry to stabilize and the tracking loop to settle to the step
change in input position. After tTRACK, a SAMPLE pulse must be
applied, releasing the LOT and DOT pins to the state deter-
mined by the fault detection circuitry and providing valid
position data at the parallel and serial outputs (note that if
position data is being acquired via the encoder outputs, they
may be monitored during tTRACK).
The RESET pin is internally pulled up.
tRST
04406-0-010
VDD
RESET
4.75V
VALID
OUTPUT
DATA
SAMPLE
LOT
DOS
tTRACK
Figure 10. Power Supply Sequencing and Reset
CHARGE PUMP OUTPUT
A 204.8 kHz square wave output with 50% duty cycle is avail-
able at the CPO output pin of the AD2S1200. This square wave
output can be used for negative rail voltage generation, or to
create a VCC rail.
相關PDF資料 |
PDF描述 |
|---|---|
| AD2S1205YSTZ | IC ADC R/D 12BIT W/OSC 44-LQFP |
| AD2S1210ASTZ-RL7 | IC CONV R/D 10-16BIT OSC 48LQFP |
| AD2S44-UM18B | IC CONV SYNC/R-D 14BIT 2CH 32DIP |
| AD2S80AUD | IC R/D CONV TRACKING 40CDIP |
| AD2S83APZ-REEL | IC CONV R/D MONO VAR RES 44PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD2S1200WSTZSTZ | 制造商:Analog Devices 功能描述:ANAAD2S1200WSTZ |
| AD2S1200YST | 制造商:Analog Devices 功能描述:Resolver to Digital 12-Bit Parallel/Serial (3-Wire, SPI) 制造商:Rochester Electronics LLC 功能描述:12-BIT R/D CONVERTER W/REF OSCILLATOR - Bulk 制造商:Analog Devices 功能描述:IC 12BIT ADC REF OSC SMD 2S1200 |
| AD2S1200YSTZ | 功能描述:IC CONV R/D 12-BIT W/OSC 44-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Data Converter Basics 標準包裝:1 系列:- 類型:電機控制 分辨率（位）:12 b 采樣率（每秒）:1M 數據接口:串行，并聯 電壓電源:單電源 電源電壓:2.7 V ~ 3.6 V，4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:100-TQFP 供應商設備封裝:100-TQFP（14x14） 包裝:剪切帶 (CT) 其它名稱:296-18373-1 |
| AD2S1200YSTZ | 制造商:Analog Devices 功能描述:IC 12BIT ADC REF OSC SMD 2S1200 |
| AD2S1200YSTZSTZ | 制造商:Analog Devices 功能描述:ANAAD2S1200YSTZ |
發布緊急采購，3分鐘左右您將得到回復。