- 您現在的位置：買賣IC網 > PDF目錄375230 > AD1893JN (ANALOG DEVICES INC) Low Cost SamplePort 16-Bit Stereo Asynchronous Sample Rate Converter PDF資料下載
參數資料
| 型號： | AD1893JN |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 消費家電 |
| 英文描述： | Low Cost SamplePort 16-Bit Stereo Asynchronous Sample Rate Converter |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PDIP28 |
| 封裝： | 0.600 INCH, PLASTIC, DIP-28 |
| 文件頁數： | 13/20頁 |
| 文件大?。?/td> | 216K |
| 代理商： | AD1893JN |
AD1893
REV. A
–13–
OPERATING FEATURES
Serial Input/Output Ports
The AD1893 uses the frequency of the left/
right
input clock
(L
R
_ I) and the left/
right
output clock (L
R
_O) signals to deter-
mine the sample rate ratio, and therefore these signals must run
continuously and transition twice per sample period. (The L
R
_I
clock frequency is equivalent to F
SIN
and the L
R
_O clock fre-
quency is equivalent to F
SOUT
.) The other clocks (WCLK_I,
WCLK_O, BCLK_I, BCLK_O) are edge sensitive and may be
used in a gated or burst mode (i.e., a stream of pulses during
data transmission or reception followed by periods of inactivity).
The word clocks and the output bit clock are used only to write
data into or read data out of the serial ports; only the left/
right
clocks are used in the internal DSP blocks. The input bit clock
is used to sample the input left/
right
clock. It is important that
the left/
right
clocks are “clean” with monotonic rising and falling
edge transitions and no excessive overshoot or undershoot which
could cause false triggering on the AD1893.
The AD1893’s flexible serial input and output ports consume
and produce data in twos-complement, MSB-first format. The
left channel data field always precedes the right channel data
field; the current channel being consumed or produced is indi-
cated by the state of the left/
right
clock (L
R
_I and L
R
_O). A left
channel field, right channel field pair is called a frame. The
input data field consists of 4 to 16 bits. The output data field
consists of 4 to 24 bits. The input signals are specified to TTL
logic levels, and the outputs swing to full CMOS logic levels.
The ports are configured by pin selections.
Serial I/O Port Modes
The AD1893 has pin-selectable bit clock polarity for the input
and output ports. In “normal” mode (BKPOL_I or BKPOL_O
LO) the data is valid on the rising edge. In the “inverted” mode
(BKPOL_I or BKPOL_O HI) the data is valid on the falling
edge. Both modes are shown in Figures 23 and 24.
The AD1893 uses two multiplexed input pins to control the mode
configuration of the input and output serial ports. MODE0_I
and MODE1_I control the input serial port, and MODE0_O
and MODE1_O control the output serial port as follows:
MODE0_I
MODE1_I
Serial Input Port Mode
0
0
Left-justified, no MSB delay, L
R
_I clock
triggered.
Left-justified, MSB delay, L
R
_I clock
triggered.
Right-justified, MSB delayed 16-bit clock
periods from L
R
_I clock transition, L
R
_I
clock triggered.
Word clock triggered, no MSB delay.
0
1
1
0
1
1
MODE0_O MODE1_O Serial Output Port Mode
0
0
Left-justified, no MSB delay, L
R
_O clock
triggered.
Left-justified, MSB delay, L
R
_O clock
triggered.
Right-justified, MSB delayed 16-bit clock
periods from L
R
_O clock transition, L
R
_O
clock triggered.
Word clock triggered, no MSB delay.
0
1
1
0
1
1
The MSB delay is useful for I
2
S format compatibility and for
ease of interfacing to some DSP processors.
The AD1893 SamplePort serial ports operate in either the word
clock (WCLK_I, WCLK_O) triggered mode or left/
right
clock
(L
R
_I, L
R
_O) triggered mode. These modes can be utilized
independently for the input and output ports. In the word clock
triggered mode, as shown in Figure 23, after the left/
right
clock
is valid, the appearance of the MSB of data is synchronous with
the rising edge of the word clock. Note that the word clock is
rising edge sensitive, and can fall anytime after it is sampled HI
by the bit clock. In the left-justified left/
right
clock triggered
modes, as shown in Figure 24, the appearance of the MSB of
data is synchronous with the rising edge of the left/
right
clock
for the left channel and the falling edge of left/
right
clock for the
right channel. The MSB is delayed by one bit clock after the
left/
right
clock if the MSB delay mode is selected. In the right-
justified left/
right
clock triggered mode, as shown in Figure 25,
the MSB is delayed 16 bit clock periods from a left/
right
clock
edge, so that when there are 64 bit clock periods per frame, the
LSB is right-justified to a left/
right
clock edge. The word clock
is not required in the left/
right
clock triggered modes, and
should be tied either HI or LO. Figure 24 shows the bit clock in
the optional gated or burst mode; the bit clock is inactive be-
tween data fields, and can take either the HI state or the LO
state while inactive.
Note that there is no requirement for a delay between the left
channel data and the right channel data. The left/
right
clocks
and the word clocks can transition immediately after the LSB of
the data, so that the MSB of the subsequent channel appears
without any timing delay. The AD1893 is therefore capable of a
32-bit frame mode, in which both 16-bit channels are packed
into a 32-bit clock period. More generally, there is no particular
requirement for when the left/
right
clock falls (i.e., there is no
left/
right
clock duty cycle or pulsewidth specification), provided
that the left/
right
clock frequency equals the intended sample
frequency, and there are sufficient bit clock periods to clock in
or out the intended number of data bits.
On-Chip Oscillator
The AD1893 includes an on-chip oscillator so that the user
need only supply an external quartz crystal or ceramic resonator.
The crystal or the resonator should be tied to the XTAL_I and
XTAL_O pins of the AD1893. An external crystal oscillator can
be used to overdrive the AD1893 on-chip oscillator. The exter-
nal clock source should be applied to the XTAL_I pin, and the
XTAL_O pin should be left unconnected.
AD1893
XTAL_I
XTAL_O
AD1893
XTAL_I
XTAL_O
NC
16MHz CRYSTAL CONNECTION
16MHz OSCILLATOR CONNECTION
16MHz
16MHz
20–64pF
20–64pF
Figure 9. Crystal and Oscillator Connections
相關PDF資料 |
PDF描述 |
|---|---|
| AD1893JST | Low Cost SamplePort 16-Bit Stereo Asynchronous Sample Rate Converter |
| AD1893 | Low Cost SamplePort 16-Bit Stereo Asynchronous Sample Rate Converter(低成本采樣端口16位立體聲異步采樣率轉換器) |
| AD1895 | 3 V/5 V Digital Audio Receiver,External APLL(數字音頻接收器) |
| AD1970 | Digital BTSC Encoder with Integrated ADC and DAC |
| AD1970JSTZ | Digital BTSC Encoder with Integrated ADC and DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD1893JNZ | 制造商:Analog Devices 功能描述:Sample Rate Converter 28-Pin PDIP W |
| AD1893JST | 制造商:Analog Devices 功能描述:Sample Rate Converter 44-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:LOW COST ASRC 44-PIN TQFP - Tape and Reel 制造商:Analog Devices 功能描述:IC ASR CONVERTER 16 BIT |
| AD1893JSTZ | 功能描述:IC SAMPLE-RATE CONV 16BIT 44TQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻處理 系列:SamplePort™ 其它有關文件:STA321 View All Specifications 標準包裝:1 系列:Sound Terminal™ 類型:音頻處理器 應用:數字音頻 安裝類型:表面貼裝 封裝/外殼:64-LQFP 裸露焊盤 供應商設備封裝:64-LQFP EP（10x10） 包裝:Digi-Reel® 其它名稱:497-11050-6 |
| AD1893JSTZRL | 功能描述:IC SAMPLE-RATE CONV 16BIT 44TQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻處理 系列:SamplePort™ 其它有關文件:STA321 View All Specifications 標準包裝:1 系列:Sound Terminal™ 類型:音頻處理器 應用:數字音頻 安裝類型:表面貼裝 封裝/外殼:64-LQFP 裸露焊盤 供應商設備封裝:64-LQFP EP（10x10） 包裝:Digi-Reel® 其它名稱:497-11050-6 |
| AD1895 | 制造商:AD 制造商全稱:Analog Devices 功能描述:192 kHz Stereo Asynchronous Sample Rate Converter |
發布緊急采購，3分鐘左右您將得到回復。