- 您現在的位置：買賣IC網 > PDF目錄375227 > ACPM-7813-TR1 CDMA/AMPS Power Amplifier Module PDF資料下載
參數資料
| 型號： | ACPM-7813-TR1 |
| 英文描述： | CDMA/AMPS Power Amplifier Module |
| 中文描述： | 碼分多址/ AMPS二元功率放大器模塊 |
| 文件頁數： | 11/21頁 |
| 文件大?。?/td> | 183K |
| 代理商： | ACPM-7813-TR1 |
11
Design Tips to use Vcntl pin
Power Mode
PA_ON
Vcntl
Power Range
Shut Down
LOW
0V
—
High Power
HIGH
2.5V
≤
28.5 dBm
To Duplexer
Battery
Vcntl
PA
TxIC
Switch Circuit for PA
Baseband
IC
PA_ON
Enable
Vdd1
Vdd2
Vbias
Vcntl
PMIC or LDO
Note: PMIC: Power Management IC
LDO: Low Drop Output (Regulator)
Power Amplifier Control Using Vcntl
Pin on ACPM-7813
Power amplifier control scheme
in CDMA systems is one of the
important and challenging
aspects of CDMA-based handset
design. Handset designers must
balance maintaining adequate
linearity while optimizing
efficiency at high, medium and
low output power levels. The
primary method to achieve these
goals is to adjust the bias of the
PA as a function of output power.
Theoretically, the best efficiency
would be achieved when the bias
of the PA is continually adjusted
based on the output power
requirement of the PA. However,
implementing this type of circuit
can be complex and costly.
Therefore several different
approaches have been developed
to provide an acceptable trade-
off between optimum efficiency
and optimum manufacturability.
This application section reviews
four methods of controlling the
bias of a CDMA power amplifier:
fixed, step, logical and dynamic.
1. Fixed Bias Control
Using a fixed bias point on the
PA is the traditional method, and
it is the simplest. For example, a
fixed control voltage of 2.5V is
recommended when using
Agilent’s Power Amplifier, 2.5V
Vcntl for ACPM-7813. The Vcntl
pin on the PA is controlled by
PA_ON pin of the baseband IC.
When PA_ON is HIGH, the output
RF signal of the PA is enabled,
enabling the subscriber unit to
transmit the required data. The
switch circuit also controls the
on/off state of the PA.
Below is an example of how to
control the operation of the
ACPM-7813 using the PA_ON and
Vcntl pin of the PA.
相關PDF資料 |
PDF描述 |
|---|---|
| ACS704ELC-015 | Fully Integrated, Hall Effect-Based Linear Current Sensor with Voltage Isolation and a Low-Resistance Current Conductor |
| ACS704ELC-005 | Fully Integrated, Hall Effect-Based Linear Current Sensor with Voltage Isolation and a Low-Resistance Current Conductor |
| ACS750LCA-075 | CURRENT SENSOR ACS750 X CA -075 |
| ACS750SCA-050 | Current Sensor |
| ACS750LCA-050 | Current Sensor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ACPM-7821 | 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:4 x 4 Power Amplifier Module for J-CDMA (898 - 925 MHz) |
| ACPM-7821-BLK | 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:4 x 4 Power Amplifier Module for J-CDMA (898 - 925 MHz) |
| ACPM-7821-TR1 | 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:4 x 4 Power Amplifier Module for J-CDMA (898 - 925 MHz) |
| ACPM-7822 | 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:JCDMA 4x4 Power Amplifier Module (898-925MHz) |
| ACPM-7822-BLK | 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:JCDMA 4x4 Power Amplifier Module (898-925MHz) |
發布緊急采購，3分鐘左右您將得到回復。