- 您現在的位置：買賣IC網 > PDF目錄375099 > A1184LUA (Allegro MicroSystems, Inc.) Standard Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches PDF資料下載
參數資料
| 型號： | A1184LUA |
| 廠商： | Allegro MicroSystems, Inc. |
| 元件分類： | 霍爾效應傳感器 |
| 英文描述： | Standard Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| 中文描述： | 標準的二線現場可編程斬波穩定單極霍爾效應開關 |
| 文件頁數： | 7/14頁 |
| 文件大小： | 317K |
| 代理商： | A1184LUA |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁
7
A1184-DS, Rev. 2
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
115 Northeast Cutoff, Box 15036
Allegro MicroSystems, Inc.
Standard Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall Effect Switch
A1184
Chopper Stabilization Technique
A limiting factor for switchpoint accuracy when using Hall
effect technology is the small signal voltage developed across
the Hall element. This voltage is proportionally small relative to
the offset that can be produced at the output of the Hall sensor
device. This makes it difficult to process the signal and maintain
an accurate, reliable output over the specified temperature and
voltage range.
Figure 2. Chopper stabilization circuit (dynamic quadrature offset cancellation)
Amp
Regulator
Clock/Logic
Hall Element
S
H
Low-Pass
Filter
Chopper stabilization is a unique approach used to minimize
Hall offset on the chip. The Allegro patented technique, dynamic
quadrature offset cancellation, removes key sources of the output
drift induced by temperature and package stress. This offset
reduction technique is based on a signal modulation-demodula-
tion process. The undesired offset signal is separated from the
magnetically induced signal in the frequency domain through
modulation. The subsequent demodulation acts as a modulation
process for the offset causing the magnetically induced signal
to recover its original spectrum at base band while the dc offset
becomes a high frequency signal. Then, using a low-pass filter,
the signal passes while the modulated dc offset is suppressed.
The chopper stabilization technique uses a 200 kHz high fre-
quency clock. For demodulation process, a sample-and-hold
technique is used, where the sampling is performed at twice
the chopper frequency (400KHz). The sampling demodulation
process produces higher accuracy and faster signal processing
capability. Using this chopper stabilization approach, the chip is
desensitized to the effects of temperature and stress. This tech-
nique produces devices that have an extremely stable quiescent
Hall output voltage, is immune to thermal stress, and has precise
recoverability after temperature cycling. This technique is made
possible through the use of a BiCMOS process which allows the
use of low-offset and low-noise amplifiers in combination with
high-density logic integration and sample-and-hold circuits.
The repeatability of switching with a magnetic field is slightly
affected using a chopper technique. The Allegro high frequency
chopping approach minimizes the affect of jitter and makes it
imperceptible in most applications. Applications that may notice
the degradation are those that require the precise sensing of alter-
nating magnetic fields such as ring magnet speed sensing. For
those applications, Allegro recommends the “l(fā)ow jitter” family
of digital sensors.
相關PDF資料 |
PDF描述 |
|---|---|
| A1184LUA-T | Standard Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| A1184LLHLT | Standard Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| A1184LLHLT-T | Standard Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| A1184 | Two-Wire, Programmable, Chopper-Stabilized, Unipolar Hall-Effect Switch |
| A1184EUA | Standard Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1184LUA-T | 功能描述:IC SWITCH HALL EFFECT UNI 3-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| A1185 | 制造商:Quick 功能描述:TSOJ 13 X 10 NOZZLE FOR QUICK957/957D |
| A118-5 | 制造商:APEM 功能描述: |
| A1185_06 | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Ultrasensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| A1185B | 制造商:HAKKO Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。