參數資料
型號: 99026
廠商: IXYS Corporation
英文描述: HALF BRIDGE DRIVER Evaluation Board
中文描述: 半橋驅動器評估板
文件頁數: 5/8頁
文件大?。?/td> 839K
代理商: 99026
5
EVBD4400
OPERATION:
For performance evaluation and power
system design please note the following:
a) The assembled board can be ran with the
IXDP630/631 removed by applying comple-
mentary 5V square waves with proper "dead
time" to the input pins INL (P1-3) and INH (P1-
2).
For standard IXDP630 operation, R17
and C22 have been loaded with their respec-
tive values represented on the bill of materi-
als. These values are for demonstration and
may not be appropriate for your application.
Change values as needed. For IXDP631
operation, load R17, C22, C23 with the rec-
ommended load components as outlined in
the IXDP630/631 data sheet along with the
crystal at the frequency of choice. R17 and
C22 serve a dual purpose depending on
which dead timer is selected.
d) Figure 4 shows the load terminated at point
A. This point could be connected to a number of
places depending on the application. For ex-
ample: Connection to ground will test the high
side device. Connection to DC BUS will test the
low side device. It could also be connected to
the center point of a capacitive divider (UPS
systems).
e) Figure 5 shows a three phase power system
implementation with a load configured in a Y
(star). It could also be configured in a DELTA
configuration. Please note the grounding
scheme. Cut the connection between "ground
plane 2" and "ground plane 4" on the compo-
nents side of the PCB and solder a 10 Ohm
resistor between these ground planes. The GND
of each board is terminated to a single ground
point.
c) Before using the PCB at full power or at-
tempting a short circuit test, make sure that a
proper high voltage electroytic capacitor is
connected between DC BUS and GND as
shown in Figure 4. The leads to this capacitor
should be as short as possible to minimize any
stray inductance.
b) Be careful with ground connections.
Avoid ground loops. In general, connect the
grounds as shown in Figure 4 to minimize
ground bounce effects. This is particularly
important when three "High/Low side driver
design kits" are connected together with a
single IXDP630 to form a three phase drive
system, such as that shown in Figure 5.
To add phases 'S' and / or 'T', enable
phases with jumpers at JP1 and/or JP2 and
apply PWM phase drive signals to TP7 and/
or TP8 taking the respective complementary
outputs from TP3 through TP6. Note that
TP1-TP15 are through-hole pads that have
been added to the board to serve as conve-
nient solder and / or test points.
If additional 'slave' boards are to be
used for mutiple phase operation, R17 -
R19, C20 - C23, and Y1 do not need to be
installed on the addtional slave boards.
The IXDP630 is hardwired for phase
'R' operation, see 630/631 data sheet, with
pins OUTENA, ENAR, and RESET tied high.
PWM drive input signal for ' R' phase is
applied to P1-6.
相關PDF資料
PDF描述
99227 PolarHV Power MOSFET
9953A Dual P-Channel Enhancement Mode MOSFET
9EL2 Axial Lead Resettable Fuses .
9EL3 Axial Lead Resettable Fuses .
A-20GV2 SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 0.5A, 125VDC, 14.4mm, PANEL MOUNT
相關代理商/技術參數
參數描述
990260 制造商:Weidmuller 功能描述:RS-MR 20B-L4 CABLE INTERFACE -EA - Bulk
9902-60BLK 功能描述:LEAD STK SHROUD BAN PLUG BLK 60" RoHS:否 類別:測試設備 >> 測試引線 - 香蕉,量表接口 系列:9902 標準包裝:1 系列:6570 類型:插接線 配置:香蕉插頭至短頭鱷魚夾 第一連接器:香蕉插頭,單,屏蔽,直角 第二連接器:接線夾,隔離型,特大號 線纜長度:60.0"(1524.00mm) 所含物品:1 根引線,紅 材料 - 絕緣體:硅樹脂 堆疊方法:不可堆疊 線規:18 AWG 電壓 - 額定:1000V(1kV) 額定電流:20A 額定值:CAT III 1000V,IEC 1010
9902-60RED 功能描述:LEAD STK SHROUD BAN PLUG RED 60" RoHS:否 類別:測試設備 >> 測試引線 - 香蕉,量表接口 系列:9902 標準包裝:1 系列:6570 類型:插接線 配置:香蕉插頭至短頭鱷魚夾 第一連接器:香蕉插頭,單,屏蔽,直角 第二連接器:接線夾,隔離型,特大號 線纜長度:60.0"(1524.00mm) 所含物品:1 根引線,紅 材料 - 絕緣體:硅樹脂 堆疊方法:不可堆疊 線規:18 AWG 電壓 - 額定:1000V(1kV) 額定電流:20A 額定值:CAT III 1000V,IEC 1010
9902612 制造商: 功能描述: 制造商:ITT Interconnect Solutions 功能描述: 制造商:undefined 功能描述:
9902622 制造商:OSM 功能描述: