- 您現在的位置：買賣IC網 > PDF目錄25526 > 95V850AGLF-T (INTEGRATED DEVICE TECHNOLOGY INC) 95V SERIES, PLL BASED CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO48 PDF資料下載
參數資料
| 型號： | 95V850AGLF-T |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘及定時 |
| 英文描述： | 95V SERIES, PLL BASED CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO48 |
| 封裝： | 0.240 INCH, LEAD FREE, MO-153, TSSOP-48 |
| 文件頁數： | 10/10頁 |
| 文件大?。?/td> | 151K |
| 代理商： | 95V850AGLF-T |
9
ICS95V850
0458G—11/21/08
General Layout Precautions:
Use copper flooded ground on the top signal layer under the
clock buffer The area under U1 on the right is an example.
Flood over the ground vias.
1)
Use power vias for power and ground. Vias 20 mil or
larger in diameter have lower high frequency impedance.
Vias for signals may be minimum drill size.
2)
Make all power and ground traces are as wide as the via
pad for lower inductance.
3)
VAA for pin 16 has a low pass RC filter to decouple the
digital and analog supplies. The 4.7uF capacitors may be
replaced with a single low ESR device with the same
total capacitance. VAA is routed on a outside signal
layer. Do not cut a power or ground plane and route in it.
4)
Notice that ground vias are never shared.
5)
When ever possible, VCC (net V2P5 in the schematic)
pins have a decoupling capacitor. Power is always routed
from the plane connection via to the capacitor pad to the
VCC pin on the clock buffer. Moats or plane cuts are not
used to isolate power.
6)
Differential mode clock output traces are routed:
a.
With a ground trace between the pairs. Trace is
grounded on both ends.
b.
Without a ground trace, clock pairs are routed with a
separation of at least 5 times the thickness of the
dielectric. If the dielectric thickness is 4.5 mil, the
trace separation is at least 18 mils.
7) Terminate differential CLK_IN and FB_IN traces after
routing to buffer pads.
Component Values:
Ref Desg.
Value
Description
Package
C1,C4,C5,
C7,C11,C12
.01uF
CERAMIC MLC
0603
C2,C3,C8,
C9
4.7uF
CERAMIC MLC
1206
C10
.22uF
CERAMIC MLC
0603
C6
2200pF
CERAMIC MLC
0603
R9,R12
120
0603
R9
4.7
0603
U1
ICS95V850
TSSOP48
Recommended Layout for the ICS95V850
相關PDF資料 |
PDF描述 |
|---|---|
| 95V857AG-130LF-T | 95V SERIES, PLL BASED CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO48 |
| 95V857AG-130T | 95V SERIES, PLL BASED CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO48 |
| 95V857AL-130T | 95V SERIES, PLL BASED CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO48 |
| 95V857AL-130T-LF | 95V SERIES, PLL BASED CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO48 |
| 95V857AL-130LF-T | 95V SERIES, PLL BASED CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 95V857AG | 功能描述:IC CLK BUF DDR 233MHZ 1CIRC 制造商:idt, integrated device technology inc 系列:- 包裝:管件 零件狀態:過期 PLL:是 主要用途:存儲器，DDR 輸入:時鐘 輸出:SSTL-2 電路數:1 比率 - 輸入:輸出:1：10 差分 - 輸入:輸出:是/是 頻率 - 最大值:233MHz 電壓 - 電源:2.3 V ~ 2.7 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TFSOP（0.240"，6.10mm 寬） 供應商器件封裝:48-TSSOP 標準包裝:39 |
| 95V857AGILF | 功能描述:時鐘驅動器及分配 RoHS:否 制造商:Micrel 乘法/除法因子:1:4 輸出類型:Differential 最大輸出頻率:4.2 GHz 電源電壓-最大: 電源電壓-最小:5 V 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-8 封裝:Reel |
| 95V857AGILFT | 功能描述:時鐘驅動器及分配 RoHS:否 制造商:Micrel 乘法/除法因子:1:4 輸出類型:Differential 最大輸出頻率:4.2 GHz 電源電壓-最大: 電源電壓-最小:5 V 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-8 封裝:Reel |
| 95V857AGLF | 功能描述:時鐘驅動器及分配 RoHS:否 制造商:Micrel 乘法/除法因子:1:4 輸出類型:Differential 最大輸出頻率:4.2 GHz 電源電壓-最大: 電源電壓-最小:5 V 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-8 封裝:Reel |
| 95V857AGLFT | 功能描述:時鐘驅動器及分配 RoHS:否 制造商:Micrel 乘法/除法因子:1:4 輸出類型:Differential 最大輸出頻率:4.2 GHz 電源電壓-最大: 電源電壓-最小:5 V 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。