- 您現在的位置：買賣IC網 > PDF目錄24832 > 935270054157 (NXP SEMICONDUCTORS) 1 CHANNEL(S), 3M bps, SERIAL COMM CONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | 935270054157 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 1 CHANNEL(S), 3M bps, SERIAL COMM CONTROLLER, PQFP64 |
| 封裝： | 10 X 10 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-314-2, LQFP-64 |
| 文件頁數： | 17/48頁 |
| 文件大小： | 657K |
| 代理商： | 935270054157 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
Philips Semiconductors
SC16C750
Universal Asynchronous Receiver/Transmitter (UART) with 64-byte FIFO
Product data
Rev. 03 — 14 March 2003
24 of 45
9397 750 11203
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
7.6 Modem Control Register (MCR)
This register controls the interface with the modem or a peripheral device.
Table 18:
Modem Control Register bits description
Bit
Symbol
Description
7
MCR[7]
Reserved. Set to 0.
6
MCR[6]
Reserved. Set to 0.
5
MCR[5]
Reserved. Set to 0.
4
MCR[4]
Loop-back. Enable the local loop-back mode (diagnostics). In this
mode the transmitter output (TX) and the receiver input (RX), CTS,
DSR, DCD, and RI are disconnected from the SC16C750 I/O pins.
Internally the modem data and control pins are connected into a
loop-back data conguration (see Figure 5). In this mode, the receiver
and transmitter interrupts remain fully operational. The Modem
Control Interrupts are also operational, but the interrupts’ sources are
switched to the lower four bits of the Modem Control. Interrupts
continue to be controlled by the IER register.
Logic 0 = Disable loop-back mode (normal default condition).
Logic 1 = Enable local loop-back mode (diagnostics).
3
MCR[3]
OUT2, INTx enable. Used to control the modem DCD signal in the
loop-back mode.
Logic 0 = Forces INT output to the 3-State mode. In the loop-back
mode, sets OUT2 (DCD) internally to a logic 1.
Logic 1 = Forces the INT output to the active mode. In the
loop-back mode, sets OUT2 (DCD) internally to a logic 0.
2
MCR[2]
OUT1. This bit is used in the Loop-back mode only. In the loop-back
mode, this bit is used to write the state of the modem RI interface
signal via OUT1.
1
MCR[1]
RTS
Logic 0 = Force RTS output to a logic 1 (normal default condition).
Logic 1 = Force RTS output to a logic 0.
0
MCR[0]
DTR
Logic 0 = Force DTR output to a logic 1 (normal default condition).
Logic 1 = Force DTR output to a logic 0.
相關PDF資料 |
PDF描述 |
|---|---|
| 08051C103JA74A | General Specifications |
| 935270056529 | 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC68 |
| 935270056518 | 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC68 |
| 935270057557 | 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQFP80 |
| 935270056512 | 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 935270713557 | 制造商:NXP Semiconductors 功能描述:SUB ONLY IC CHP |
| 935270792551 | 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA |
| 935270792557 | 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA |
| 935270793551 | 制造商:NXP Semiconductors 功能描述:IC BUS TRCVR 3-ST 16BIT 56VFBGA |
| 935270793557 | 制造商:NXP Semiconductors 功能描述:IC BUS TRCVR 3-ST 16BIT 56VFBGA |
發布緊急采購，3分鐘左右您將得到回復。