- 您現在的位置：買賣IC網 > PDF目錄36334 > 935242210551 (NXP SEMICONDUCTORS) SPECIALTY CONSUMER CIRCUIT, PQFP160 PDF資料下載
參數資料
| 型號： | 935242210551 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP160 |
| 封裝： | PLASTIC, SOT-322, QFP-160 |
| 文件頁數： | 30/147頁 |
| 文件大?。?/td> | 526K |
| 代理商： | 935242210551 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁
1998 Apr 09
125
Philips Semiconductors
Product specication
Multimedia bridge, high performance
Scaler and PCI circuit (SPCI)
SAA7146A
7.17.2.2
Example
The protocol sequence for reading three bytes with
subaddress access is illustrated in Fig.43. The procedure
for this read operation is detailed below:
1. Address slave, write to IICTFR (see Fig.44):
BYTE2 [7:1] = DA, BYTE2 [0] = 0 (write),
ATTR2 = START
BYTE1 = subaddress, ATTR1 = CONT
BYTE0 [7:1] = DA, BYTE0 [0] = 1(read),
ATTR0 = START
2. Wait until BUSY = 0
3. Check ERR bit, if it is inactive the slave target is
successfully addressed
4. Transfer data, write attribute information to IICTFR
(see Fig.45):
BYTE2 = first received data byte, ATTR2 = CONT
BYTE1 = second received data byte, ATTR1 = CONT
BYTE0 = third received data byte, ATTR0 = STOP
5. Wait until BUSY = 0
6. Check ERR bit, if it is inactive IICTFR contains valid
data.
Instead of checking the general error flag (ERR) after each
single 3-byte sequence, it is possible to check the ERR at
the end of the whole protocol sequence. During a bus
cycle, the BUSY bit is set HIGH. At the end of a bus cycle
an interrupt request is generated if enabled and BUSY is
cleared if no error occurs. Writing to the IICTRF should not
be done while the BUSY bit is active, otherwise the ERR
flag will be set HIGH. If no transfer errors occur during the
three transfer actions, the ERR bit will be set LOW. If an
error occurs the ERR bit will be set HIGH and the BUSY bit
stays HIGH. In this case the error and BUSY flags have to
be cleared before starting a new operation.
Fig.43 Protocol sequence for reading three bytes with subaddress access.
handbook, full pagewidth
S
W
A
DA
SA
address device and transmit subaddress
S
R
A
DA
D
restart for reading from slave
receive data
P
MGD696
A
NA
D
restart last byte and STOP
receive data
相關PDF資料 |
PDF描述 |
|---|---|
| 935242210557 | SPECIALTY CONSUMER CIRCUIT, PQFP160 |
| 935262922551 | SPECIALTY CONSUMER CIRCUIT, PQFP160 |
| 935262922557 | SPECIALTY CONSUMER CIRCUIT, PQFP160 |
| 935242220551 | SPECIALTY CONSUMER CIRCUIT, PQFP208 |
| 935242220557 | SPECIALTY CONSUMER CIRCUIT, PQFP208 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 935245650125 | 制造商:NXP Semiconductors 功能描述:Inverter 1-Element CMOS 5-Pin TSSOP T/R |
| 935248-90 | 制造商:JANCO 功能描述:935248-90 |
| 9-3525-012 | 制造商:KEYSTONE 功能描述:MODIFIED 3525,VERSION E |
| 935252-5 | 制造商:C-H 功能描述:935252-5 |
| 935257650112 | 制造商:NXP Semiconductors 功能描述:SUB ONLY ICSUBS TO 935257650112 |
發布緊急采購，3分鐘左右您將得到回復。