- 您現在的位置：買賣IC網 > PDF目錄376479 > 89C55 (Atmel Corp.) 8-Bit Microcontroller with 20K Bytes Flash PDF資料下載
參數資料
| 型號： | 89C55 |
| 廠商： | Atmel Corp. |
| 英文描述： | 8-Bit Microcontroller with 20K Bytes Flash |
| 中文描述： | 8位閃存微控制器20,000字節 |
| 文件頁數： | 3/24頁 |
| 文件大?。?/td> | 606K |
| 代理商： | 89C55 |
AT89C55
4-171
The AT89C55 provides the following standard features:
20K bytes of Flash, 256-bytes of RAM, 32 I/O lines, three
16-bit timer/counters, a six-vector two-level interrupt archi-
tecture, a full duplex serial port, on-chip oscillator, and
clock circuitry. In addition, the AT89C55 is designed with
static logic for operation down to zero frequency and sup-
ports two software selectable power saving modes. The
Idle Mode stops the CPU while allowing the RAM,
timer/counters, serial port, and interrupt system to continue
functioning. The Power Down Mode saves the RAM con-
tents but freezes the oscillator, disabling all other chip func-
tions until the next hardware reset. The low-voltage option
saves power and operates with a 2.7-volt power supply.
Pin Description
V
CC
Supply voltage.
GND
Ground.
Port 0
Port 0 is an 8-bit open drain bidirectional I/O port. As an
output port, each pin can sink eight TTL inputs. When 1s
are written to port 0 pins, the pins can be used as high-
impedance inputs.
Port 0 can also be configured to be the multiplexed low-
order address/data bus during accesses to external pro-
gram and data memory. In this mode, P0 has internal pul-
lups.
Port 0 also receives the code bytes during Flash program-
ming and outputs the code bytes during program verifica-
tion. External pullups are required during program verifica-
tion.
Port 1
Port 1 is an 8-bit bidirectional I/O port with internal pullups.
The Port 1 output buffers can sink/source four TTL inputs.
When 1s are written to Port 1 pins, they are pulled high by
the internal pullups and can be used as inputs. As inputs,
Port 1 pins that are externally being pulled low will source
current (I
IL
) because of the internal pullups.
In addition, P1.0 and P1.1 can be configured to be the
timer/counter 2 external count input (P1.0/T2) and the
timer/counter 2 trigger input (P1.1/T2EX), respectively, as
shown in the following table.
Port 1 also receives the low-order address bytes during
Flash programming and verification.
Port 2
Port 2 is an 8-bit bidirectional I/O port with internal pullups.
The Port 2 output buffers can sink/source four TTL inputs.
When 1s are written to Port 2 pins, they are pulled high by
the internal pullups and can be used as inputs. As inputs,
Port 2 pins that are externally being pulled low will source
current (I
IL
) because of the internal pullups.
Port 2 emits the high-order address byte during fetches
from external program memory and during accesses to
external data memory that use 16-bit addresses (MOVX @
DPTR). In this application, Port 2 uses strong internal pul-
lups when emitting 1s. During accesses to external data
memory that use 8-bit addresses (MOVX @ RI), Port 2
emits the contents of the P2 Special Function Register.
Port 2 also receives the high-order address bits and some
control signals during Flash programming and verification.
Port 3
Port 3 is an 8-bit bidirectional I/O port with internal pullups.
The Port 3 output buffers can sink/source four TTL inputs.
When 1s are written to Port 3 pins, they are pulled high by
the internal pullups and can be used as inputs. As inputs,
Port 3 pins that are externally being pulled low will source
current (I
IL
) because of the pullups.
Port 3 also serves the functions of various special features
of the AT89C55, as shown in the following table.
Port 3 also receives the highest-order address bit and
some control signals for Flash programming and verifica-
tion.
RST
Reset input. A high on this pin for two machine cycles while
the oscillator is running resets the device.
Port Pin
Alternate Functions
P1.0
T2 (external count input to Timer/Counter 2),
clock-out
P1.1
T2EX (Timer/Counter 2 capture/reload
trigger and direction control)
Port Pin
Alternate Functions
P3.0
RXD (serial input port)
P3.1
TXD (serial output port)
P3.2
INT0 (external interrupt 0)
P3.3
INT1 (external interrupt 1)
P3.4
T0 (timer 0 external input)
P3.5
T1 (timer 1 external input)
P3.6
WR (external data memory write strobe)
P3.7
RD (external data memory read strobe)
相關PDF資料 |
PDF描述 |
|---|---|
| 89LS8252 | 8-Bit Microcontroller with 8K Bytes Flash |
| 89LV55 | 8-Bit Microcontroller with 20K Bytes Flash |
| 89S8252 | 8-Bit Microcontroller with 8K Bytes Flash |
| 8M052489 | 8m Class DC to AC Inverter |
| 8T26A | 8-Channel, 10-Bit ADC with I2C Compatible Interface in 20-Lead TSSOP; Package: TSSOP; No of Pins: 20; Temperature Range: Industrial |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 89C58 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80C51 8-bit microcontroller family 4K/8K/16K/32K Flash |
| 89C59 | 制造商:SST 制造商全稱:Silicon Storage Technology, Inc 功能描述:FlashFlex51 MCU |
| 89C61X2 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80C51 8-bit Flash microcontroller family |
| 89C664HFA | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 89-CBSAP-2.5X3.5X0.8 | 功能描述:89-CBSAP-2.5X3.5X0.8--89S14--CIR 制造商:leader tech inc. 系列:* 零件狀態:在售 類型:屏蔽，分體式 高度 - 總:0.800"（20.32mm） 長度 - 總:3.500"（88.90mm） 寬度 - 總:2.500"（63.50mm） 通風:通風孔，按樣式排列 安裝類型:通孔 標準包裝:5 |
發布緊急采購，3分鐘左右您將得到回復。