
TB-2045 Page 4 of 8
3. Dilute Statguard
Dissipative Cleaner, two (2) quarts of
cleaner concentrate to five (5) gallons of clean water.
4. Thoroughly mix the cleaner concentrate before pouring
the cleaner into the bucket. Use a clean untreated mop
(dedicated to Statguard use only) to damp mop the area.
Wring out excess fluid and do not flood a treated floor with
water. Do not use scrubbing machine to clean the floor.
5. Allow 20 to 40 minutes drying time before walking on the
cleaned area.
Clean only with Statguard Cleaner, do not damp mop with
plain water or with a high alkaline or high residue cleaner.
Using harsh detergents can damage a treated floor’s static
dissipative properties, or can turn the no-zinc finish white.
For additional usage information and a MSDS sheet on
Desco Statguard Floor Cleaner, ask for Technical Bulletin
Statfree Dissipative Spray Buff
Regular spray buffing will help to maintain floors treated
with Statfree Floor Finish at peak performance and
appearance. Spray buffing with Statfree Dissipative Spray
Buff will remove light surface soil while reviving the high
gloss and electrical properties of the treated surface.
SPRAY BUFF SCHEDULE
Heavy to moderate traffic floors should be spray buffed 1-2
times per week. Light traffic floors should be buffed once a
week or as needed.
Figure 7. Desco Statfree Spray Buff, Item No. 81050, ready-to-use, 1 quart spray bottle, case of 12
Equipment needed:
Push broom
175-1500 RPM buffing machine
Statfree Spray Buff, Item #81050 1. Always use in a well ventilated area or wear a suitable
respirator. Wear appropriate eye protection such as splash
goggles and impervious type protective gloves.
2. Sweep away all loose dirt and contaminants. Do not
spray buff on a dirty floor. If the floor is soiled, first perform
the cleaning procedure using Desco’s Statguard Floor
Cleaner.
6. Allow minimum of 48 hours of drying time before
performing any wet maintenance (restoring and spray
burnishing) on the newly coated floor.
Floor Finish Maintenance
DRY MOP PROGRAM
Keep the floor surface clean. Use an untreated dust mop or
push broom daily or as needed to remove accumulated dirt
and insulative contaminants.
Statguard Dissipative Floor Cleaner
Desco’s Statguard Dissipative Floor Cleaner is specifically
formulated to clean floors treated with Statfree Dissipative
Floor Finish. Statguard Floor Cleaner is formulated with
dissipative agents that will rejuvenate and improve the static
dissipative properties of floors treated with Statfree Floor
Finish.
Figure 6. Floor maintenance with Statguard Dissipative
Floor Cleaner, Item No.
10566, 5 gallon, concentrate
Desco’s Dissipative Cleaner effectively cleans without
leaving behind any harmful residue that can dull the surface
or impede dissipation properties. Statguard Cleaner is
a non-alkaline detergent with a neutral pH, which requires
no rinsing. Use the following procedure to clean treated
floors with Desco Statguard Cleaner. This product is also
recommended for use on conductive floor tile.
CLEANING SCHEDULE
Heavy to moderate traffic floors should be cleaned 1-2
times per week. Light traffic floors should be cleaned once
a week or as needed.
Equipment needed:
Push broom
Mop (dedicated to Statguard use only)
Buckets
Statguard Dissipative Cleaner, Item #10566 1. Always use in a well ventilated area or wear a suitable
respirator. Wear appropriate eye protection such as splash
goggles and impervious type protective gloves.
2. Dry mop the surface to be cleaned.
DESCO WEST
- 3651 Walnut Avenue, Chino, CA 91710 (909) 627-8178 Fax (909) 627-7449
DESCO EAST
- One Colgate Way, Canton, MA 02021-1407 (781) 821-8370 Fax (781) 575-0172 Web Site:
Desco.com 2010 DESCO INDUSTRIES INC.
Employee Owned