2006 Teridian Semiconductor Corporation Rev. " />
參數資料
型號: 78P2351-DB/ECLM
廠商: Maxim Integrated Products
文件頁數: 42/42頁
文件大?。?/td> 0K
描述: BOARD DEMO 78P2351 W/OPT MODULE
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 1
系列: *
78P2351
Single Channel
OC-3/ STM1-E/ E4 LIU
Page: 9 of 42
2006 Teridian Semiconductor Corporation
Rev. 2.4
SERIAL CONTROL INTERFACE
The serial port controlled register allows a generic
controller to interface with the 78P2351. It is used
for mode settings, diagnostics and test, retrieval of
status and performance information, and for on-chip
fuse trimming during production test. The SPSL pin
must be high in order to use the serial port.
The serial interface consists of four pins: Serial Port
Enable (SEN_CMI), Serial Clock (SCK_MON), Serial
Data In (SDI_PAR), and Serial Data Out (SDO_E4).
The SEN_CMI pin initiates the read and write
operations.
It can also be used to select a
particular device allowing SCK_MON, SDI_PAR
and SDO_E4 to be bussed together.
SCK_MON is the clock input that times the data
on SDI_PAR and SDO_E4. Data on SDI_PAR
is latched in on the rising-edge of SCK_MON,
and data on SDO_E4 is clocked out using the
falling edge of SCK_MON.
SDI_PAR is used to insert mode, address, and
register data into the chip. Address and Data
information are input least significant bit (LSB)
first. The mode and address bit assignment and
register table are shown in the following section.
SDO_E4 is a tri-state capable output. It is used
to output register data during a read operation.
SDO_E4 output is normally high impedance,
and is enabled only during the duration when
register data is being clocked out. Read data is
clocked out least significant bit (LSB) first.
If SDI_PAR coming out of the micro-controller chip is
also tri-state capable, SDI_PAR and SDO_E4 can
be connected together to simplify connections.
PROGRAMMABLE INTERRUPTS
In addition to the receiver LOS and LOL status pins,
the 78P2351 provides a programmable interrupt for
the transmitter. In HW control mode, the default
functions of the Tx interrupt is a transmit Loss of
Lock (TXLOL) or FIFO error (FERR).
相關PDF資料
PDF描述
M1RXK-2640K IDC CABLE - MPR26K/MC26F/X
GSM08DRTN-S13 CONN EDGECARD 16POS .156 EXTEND
M3WWK-2606J IDC CABLE - MPL26K/MC26G/MPL26K
GMM08DRTN-S13 CONN EDGECARD 16POS .156 EXTEND
383LX821M450B052VS CAP ALUM 820UF 450V 20% SNAP
相關代理商/技術參數
參數描述
78P2351-IGT 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Single Channel OC-3/ STM1-E/ E4 LIU
78P2351-IGT/F 功能描述:接口 - 專用 Single Ch OC-3/STM-1e/E4 LIU RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
78P2351-IGTR 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Single Channel OC-3/ STM1-E/ E4 LIU
78P2351-IGTR/F 功能描述:接口 - 專用 Single Ch OC-3/STM-1e/E4 LIU RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
78P2351R 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Serial 155M NRZ to CMI Converter