- 您現在的位置：買賣IC網 > PDF目錄360416 > 74ALVCH162601 (NXP Semiconductors N.V.) 18-bit universal bus transceiver with 30Ω termination resistor (3-State)(帶30Ω終端電阻器的18位通用總線收發器（三態）) PDF資料下載
參數資料
| 型號： | 74ALVCH162601 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 18-bit universal bus transceiver with 30Ω termination resistor (3-State)(帶30Ω終端電阻器的18位通用總線收發器（三態）) |
| 中文描述： | 18 -30Ω端接電阻位通用總線收發器（3態）（帶30Ω終端電阻器的18位通用總線收發器（三態）） |
| 文件頁數： | 16/20頁 |
| 文件大?。?/td> | 90K |
| 代理商： | 74ALVCH162601 |
1999 Oct 14
16
Philips Semiconductors
Product specification
18-bit universal bus transceiver with 30
termination resistor; 3-state
74ALVCH162601
SOLDERING
Introduction to soldering surface mount packages
Thistextgivesaverybriefinsighttoacomplextechnology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering is not always suitable
for surface mount ICs, or for printed-circuit boards with
high population densities. In these situations reflow
soldering is often used.
Reflow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
infrared/convection heating in a conveyor type oven.
Throughput times (preheating, soldering and cooling) vary
between 100 and 200 seconds depending on heating
method.
Typical reflow peak temperatures range from
215 to 250
°
C. The top-surface temperature of the
packages should preferable be kept below 230
°
C.
Wave soldering
Conventional single wave soldering is not recommended
forsurfacemountdevices(SMDs)orprinted-circuitboards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is
preferred
to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
Forpackageswithleadsonfoursides,thefootprintmust
be placed at a 45
°
angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°
C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| 74ALVCH162827 | 20-bit buffer/line driver, non-inverting,with 30Ω termination resistor (3-State)(同相,帶30Ω終端電阻器的20位緩沖器/線驅動器（三態）) |
| 74ALVCH16373 | 2.5V/3.3V 16-bit D-type transparent latch(3-State)(2.5V/3.3V 16位 D透明鎖存器（三態）) |
| 74ALVCH16374 | 2.5V/3.3V 16-bit edge-triggered D-type flip-flop (3-State)(2.5V/3.3V 16位邊緣觸發的D觸發器（三態）) |
| 74ALVCH16500 | Quadruple Positive-NAND Gates With Schmitt-Trigger Inputs 14-SOIC -40 to 85 |
| 74ALVCH6500 | 18-bit universal bus transceiver(18位通用總線收發器（三態）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 74ALVCH162601DG | 功能描述:總線收發器 18-BIT UNIV BUS XCVR 3-STATE RoHS:否 制造商:Fairchild Semiconductor 邏輯類型:CMOS 邏輯系列:74VCX 每芯片的通道數量:16 輸入電平:CMOS 輸出電平:CMOS 輸出類型:3-State 高電平輸出電流:- 24 mA 低電平輸出電流:24 mA 傳播延遲時間:6.2 ns 電源電壓-最大:2.7 V, 3.6 V 電源電壓-最小:1.65 V, 2.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-48 封裝:Reel |
| 74ALVCH162601DGG | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:18-bit universal bus transceiver with 30 ohm termination resistor; 3-state |
| 74ALVCH162601DGG,1 | 功能描述:總線收發器 18-BIT UNIV BUS RoHS:否 制造商:Fairchild Semiconductor 邏輯類型:CMOS 邏輯系列:74VCX 每芯片的通道數量:16 輸入電平:CMOS 輸出電平:CMOS 輸出類型:3-State 高電平輸出電流:- 24 mA 低電平輸出電流:24 mA 傳播延遲時間:6.2 ns 電源電壓-最大:2.7 V, 3.6 V 電源電壓-最小:1.65 V, 2.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-48 封裝:Reel |
| 74ALVCH162601DGG,112 | 制造商:NXP Semiconductors 功能描述: |
| 74ALVCH162601DGG,118 | 制造商:NXP Semiconductors 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。