參數資料
型號： 74ACQT373QSC
廠商： Fairchild Semiconductor Corporation
英文描述： Quiet Series⑩ Octal Transparent Latch with 3-STATE Outputs
中文描述： 安靜系列⑩八路透明鎖存器與三態輸出
文件頁數： 9/13頁
文件大?。?/td> 313K
代理商： 74ACQT373QSC
7
1989 Fairchild Semiconductor Corporation
74ACQ373, 74ACTQ373 Rev. 1.3
www.fairchildsemi.com
9
FACT Noise Characteristics
The setup of a noise characteristics measurement is
critical to the accuracy and repeatability of the tests. The
following is a brief description of the setup used to
measure the noise characteristics of FACT.
Equipment:
Hewlett Packard Model 8180A Word Generator
PC-163A Test Fixture
Tektronics Model 7854 Oscilloscope
Procedure:
1. Verify Test Fixture Loading: Standard Load 50pF,
500
.
2. Deskew the HFS generator so that no two channels
have greater than 150ps skew between them. This
requires that the oscilloscope be deskewed first. It is
important to deskew the HFS generator channels
before testing. This will ensure that the outputs switch
simultaneously.
3. Terminate all inputs and outputs to ensure proper
loading of the outputs and that the input levels are at
the correct voltage.
4. Set the HFS generator to toggle all but one output at
a frequency of 1MHz. Greater frequencies will
increase DUT heating and effect the results of the
measurement.
5. Set the HFS generator input levels at 0V LOW and
3V HIGH for ACT devices and 0V LOW and 5V HIGH
for AC devices. Verify levels with an oscilloscope.
Notes:
16. V
OHV
and V
OLP
are measured with respect to ground
reference.
17. Input pulses have the following characteristics:
f
=
1MHz, t
r
=
3ns, t
f
=
3ns, skew
<
150ps.
Figure 1. Quiet Output Noise Voltage Waveforms
V
OLP
/V
OLV
and V
OHP
/V
OHV
:
■
Determine the quiet output pin that demonstrates the
greatest noise levels. The worst case pin will usually
be the furthest from the ground pin. Monitor the output
voltages using a 50
coaxial cable plugged into a
standard SMB type connector on the test fixture.
Do not use an active FET probe.
■
Measure V
OLP
and V
OLV
on the quiet output during
the worst case transition for active and enable.
Measure V
OHP
and V
OHV
on the quiet output during
the worst case active and enable transition.
■
Verify that the GND reference recorded on the
oscilloscope has not drifted to ensure the accuracy
and repeatability of the measurements.
V
ILD
and V
IHD
:
■
Monitor one of the switching outputs using a 50
coaxial cable plugged into a standard SMB type
connector on the test fixture. Do not use an active
FET probe.
■
First increase the input LOW voltage level, V
IL
, until
the output begins to oscillate or steps out a min of 2ns.
Oscillation is defined as noise on the output LOW
level that exceeds V
IL
limits, or on output HIGH levels
that exceed V
IH
limits. The input LOW voltage level at
which oscillation occurs is defined as V
ILD
.
■
Next decrease the input HIGH voltage level, V
IH
until
the output begins to oscillate or steps out a min of 2ns.
Oscillation is defined as noise on the output LOW
level that exceeds V
IL
limits, or on output HIGH levels
that exceed V
IH
limits. The input HIGH voltage level at
which oscillation occurs is defined as V
IHD
.
■
Verify that the GND reference recorded on the
oscilloscope has not drifted to ensure the accuracy
and repeatability of the measurements.
Figure 2. Simultaneous Switching Test Circuit
相關PDF資料
PDF描述
74ACT00SCX-NL Quad 2-Input NAND Gate
74ACT04MTCX-NL CERAMIC CHIP/MIL-PRF-55681
74ACT04SCX-NL CERAMIC CHIP/MIL-PRF-55681
74ACT109 Octal Buffers/Drivers With 3-State Outputs 20-PDIP 0 to 70
74AC109MTC Dual JK Positive Edge-Triggered Flip-Flop
相關代理商/技術參數
參數描述
74ACT00 功能描述:NAND Gate IC 4 Channel Die 制造商:fairchild/micross components 系列:74ACT 包裝:托盤 零件狀態:有效 邏輯類型:與非門 電路數:4 輸入數:2 特性:- 電壓 - 電源:4.5 V ~ 5.5 V 電流 - 靜態（最大值）:2μA 電流 - 輸出高，低:24mA，24mA 邏輯電平 - 低:0.8V 邏輯電平 - 高:2V 不同 V，最大 CL 時的最大傳播延遲:9ns @ 5V，- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 供應商器件封裝:模具 封裝/外殼:模具 標準包裝:25
74ACT00B 功能描述:邏輯門 Quad 2-Input NAND RoHS:否 制造商:Texas Instruments 產品:OR 邏輯系列:LVC 柵極數量:2 線路數量（輸入/輸出）:2 / 1 高電平輸出電流:- 16 mA 低電平輸出電流:16 mA 傳播延遲時間:3.8 ns 電源電壓-最大:5.5 V 電源電壓-最小:1.65 V 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:DCU-8 封裝:Reel
74ACT00D 制造商:Texas Instruments 功能描述: 制造商:undefined 功能描述:
74ACT00M 功能描述:邏輯門 RO 511-74ACT00M-TR RoHS:否 制造商:Texas Instruments 產品:OR 邏輯系列:LVC 柵極數量:2 線路數量（輸入/輸出）:2 / 1 高電平輸出電流:- 16 mA 低電平輸出電流:16 mA 傳播延遲時間:3.8 ns 電源電壓-最大:5.5 V 電源電壓-最小:1.65 V 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:DCU-8 封裝:Reel
74ACT00MTC 功能描述:邏輯門 Qd 2-Input NAND Gate RoHS:否 制造商:Texas Instruments 產品:OR 邏輯系列:LVC 柵極數量:2 線路數量（輸入/輸出）:2 / 1 高電平輸出電流:- 16 mA 低電平輸出電流:16 mA 傳播延遲時間:3.8 ns 電源電壓-最大:5.5 V 電源電壓-最小:1.65 V 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:DCU-8 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*