- 您現在的位置：買賣IC網 > PDF目錄157285 > 5V19EE904NLGI (INTEGRATED DEVICE TECHNOLOGY INC) 5V SERIES, PLL BASED CLOCK DRIVER, 7 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), QCC32 PDF資料下載
參數資料
| 型號： | 5V19EE904NLGI |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘及定時 |
| 英文描述： | 5V SERIES, PLL BASED CLOCK DRIVER, 7 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), QCC32 |
| 封裝： | 0.50 MM PITCH, ROHS COMPLIANT, VFQFPN-32 |
| 文件頁數： | 4/29頁 |
| 文件大小： | 292K |
| 代理商： | 5V19EE904NLGI |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
IDT5V19EE904
EEPROM PROGRAMMABLE VCXO CLOCK GENERATOR
CLOCK SYNTHESIZER
IDT EEPROM PROGRAMMABLE VCXO CLOCK GENERATOR
12
IDT5V19EE904
REV H 042211
SEL[2:0] Function
The IDT5V19EE904 can support up to six unique
configurations. Users may pre-programmed all these
configurations, and select the configurations using SEL[2:0]
pins. Alternatively, users may use I2C interface to configure
these registers on-the-fly.
SD/OE Pin Function
The polarity of the SD/OE signal pin can be programmed to
be either active HIGH or LOW with the SP bit (0x02). When
SP is “0” (default), the pin becomes active HIGH and when
SP is “1”, the pin becomes active LOW. The SD/OE pin can
be configured as either to shutdown the PLLs or to
enable/disable the outputs.
1 Assert to disable the outputs whose OE bits are set
2 Assert to shut down power, on the outputs and 3-level pins
Configuration OUTx IO Standard
Users can configure the individual output IO standard from
a specified 1.8 to 3.3V power supplies. Each output can
support 1.8 to 3.3V LVTTL. OUT0 can only be a 3.3V
single-ended output.
Programming the Device
I2C may be used to program the IDT5V19EE904.
– Device (slave) address = 7'b1101010
I2C Programming
The IDT5V19EE904 is programmed through an I2C-Bus
serial interface, and is an I2C slave device. The read and
write transfer formats are supported. The first byte of data
after a write frame to the correct slave address is interpreted
as the register address; this address auto-increments after
each byte written or read.
The frame formats are shown in the following illustration.
Framing
SEL2
SEL1
SEL0
Configuration Selections
0
Select CONFIG0
0
1
Select CONFIG1
0
1
0
Select CONFIG2
0
1
Select CONFIG3
1
0
Select CONFIG4
1
0
1
Select CONFIG5
1
0
Reserved (Do not use)
1
Reserved (Do not use)
SD/O E
OE M o d e
1
S D M ode
2
SH
SP
相關PDF資料 |
PDF描述 |
|---|---|
| 5V60014DVGI8 | PLL BASED CLOCK DRIVER, PDSO8 |
| 6.0MHZ12SMX-B20100075FUNDTR | QUARTZ CRYSTAL RESONATOR, 6 MHz |
| 6.0MHZ12SMX-C201002010FUNDTR | QUARTZ CRYSTAL RESONATOR, 6 MHz |
| 6.0MHZ12SMX-B201000SRFUNDTR | QUARTZ CRYSTAL RESONATOR, 6 MHz |
| 6.0MHZ12SMX-C1001004075FUNDTR | QUARTZ CRYSTAL RESONATOR, 6 MHz |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 5V19EE904NLGI8 | 功能描述:時鐘發生器及支持產品 EEPROM PROGRAMMABLE PLL AND VCXO RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| 5V1A-ADAPTER | 制造商:Distributed By MCM 功能描述:5V 1A Switching AC Power Supply - Micro USB |
| 5V1A-USB | 制造商:Gravitech 功能描述:USB WALL ADAPTER 5V 1A |
| 5V1BC | 制造商:SEMTECH_ELEC 制造商全稱:SEMTECH ELECTRONICS LTD. 功能描述:Silicon Epitaxial Planar Zener Diodes |
| 5V1BCA | 制造商:SEMTECH_ELEC 制造商全稱:SEMTECH ELECTRONICS LTD. 功能描述:Silicon Epitaxial Planar Zener Diodes |
發布緊急采購，3分鐘左右您將得到回復。