- 您現在的位置：買賣IC網 > PDF目錄33797 > 45DB041B (Atmel Corp.) 4-megabit 2.5-volt Only or 2.7-volt Only DataFlash PDF資料下載
參數資料
| 型號： | 45DB041B |
| 廠商： | Atmel Corp. |
| 英文描述： | 4-megabit 2.5-volt Only or 2.7-volt Only DataFlash |
| 中文描述： | 4兆位2.5伏，只有2.7伏，只有上DataFlash |
| 文件頁數： | 32/33頁 |
| 文件大?。?/td> | 233K |
| 代理商： | 45DB041B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁
8
AT45DB041B
1938F–DFLSH–10/02
If a sector is programmed or reprogrammed sequentially page-by-page, then the pro-
gramming algorithm shown in Figure 1 on page 26 is recommended. Otherwise, if
multiple bytes in a page or several pages are programmed randomly in a sector, then
the programming algorithm shown in Figure 2 on page 27 is recommended. Each page
within a sector must be updated/rewritten at least once within every 10,000 cumulative
page erase/program operations in that sector.
Operation Mode
Summary
The modes described can be separated into two groups – modes which make use of the
Flash memory array (Group A) and modes which do not make use of the Flash memory
array (Group B).
Group A modes consist of:
1.
Main Memory Page Read
2.
Main Memory Page to Buffer 1 (or 2) Transfer
3.
Main Memory Page to Buffer 1 (or 2) Compare
4.
Buffer 1 (or 2) to Main Memory Page Program with Built-in Erase
5.
Buffer 1 (or 2) to Main Memory Page Program without Built-in Erase
6.
Page Erase
7.
Block Erase
8.
Main Memory Page Program through Buffer
9.
Auto Page Rewrite
Group B modes consist of:
1.
Buffer 1 (or 2) Read
2.
Buffer 1 (or 2) Write
3.
Status Register Read
If a Group A mode is in progress (not fully completed) then another mode in Group A
should not be started. However, during this time in which a Group A mode is in
progress, modes in Group B can be started.
This gives the Serial DataFlash the ability to virtually accommodate a continuous data
stream. While data is being programmed into main memory from buffer 1, data can be
loaded into buffer 2 (or vice versa). See application note AN-4 (“Using Atmel’s Serial
DataFlash”) for more details.
Pin Descriptions
SERIAL INPUT (SI): The SI pin is an input-only pin and is used to shift data into the
device. The SI pin is used for all data input including opcodes and address sequences.
SERIAL OUTPUT (SO): The SO pin is an output-only pin and is used to shift data out
from the device.
SERIAL CLOCK (SCK): The SCK pin is an input-only pin and is used to control the flow
of data to and from the DataFlash. Data is always clocked into the device on the rising
edge of SCK and clocked out of the device on the falling edge of SCK.
CHIP SELECT (CS): The DataFlash is selected when the CS pin is low. When the
device is not selected, data will not be accepted on the SI pin, and the SO pin will
remain in a high-impedance state. A high-to-low transition on the CS pin is required to
start an operation, and a low-to-high transition on the CS pin is required to end an
operation.
相關PDF資料 |
PDF描述 |
|---|---|
| 45DB081B | AT-45DB081B DATA FLASH RELIABILITY DATA |
| 45IZ | 5V or 12V Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
| 45L(R)SERIES | Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits |
| 45L(R) | STANDARD RECOVERY DIODES Stud Version |
| 45L100 | Standard Recovery Diodes(標準修復二極管) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 45DB081B | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:AT-45DB081B DATA FLASH RELIABILITY DATA |
| 45DB081B-CNC | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 45DB161B | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:16M bit dataflash 2.7V |
| 45DB642DCNU | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 45DB642D-CNU | 制造商: 功能描述: 制造商:undefined 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。