參數資料
型號: 20-101-1154
廠商: Rabbit Semiconductor
文件頁數: 50/112頁
文件大?。?/td> 0K
描述: MODULE RCM4120 RABBITCORE
標準包裝: 1
系列: RabbitCore®
模塊/板類型: MPU 核心模塊
適用于相關產品: RCM4120
其它名稱: 316-1122
38
RabbitCore RCM4100
4.4 A/D Converter (RCM4100 only)
The RCM4100 has an onboard ADS7870 A/D converter whose scaling and filtering are
done via the motherboard on which the RCM4100 module is mounted. The A/D converter
multiplexes converted signals from eight single-ended or four differential inputs to Serial
Port B on the Rabbit 4000.
The eight analog input pins, LN0–LN7, each have an input impedance of 6–7 M
,
depending on whether they are used as single-ended or differential inputs. The input signal
can range from -2 V to +2 V (differential mode) or from 0 V to +2 V (single-ended mode).
Use a resistor divider such as the one shown in Figure 9 to measure voltages above 2 V on
the analog inputs. See Appendix B.4.3 for information on how to measure negative voltages.
Figure 9. Resistor Divider Network for Analog Inputs
The R1 resistors are typically 20 k
to 100 k, with a lower resistance leading to more
accuracy, but at the expense of a higher current draw. The R0 resistors would then be
180 k
to 900 k for a 10:1 attenuator. The capacitor filters noise pulses on the A/D
converter input.
The actual voltage range for a signal going to the A/D converter input is also affected by
the 1, 2, 4, 5, 8, 10, 16, and 20 V/V software-programmable gains available on each channel
of the ADS7870 A/D converter. Thus, you must scale the analog signal with an attenuator
circuit and a software-programmable gain so that the actual input presented to the A/D
converter is within the range limits of the ADS7870 A/D converter chip (-2 V to + 2 V or
0 V to + 2 V).
The A/D converter chip can only accept positive voltages. With the R1 resistors connected
to ground, your analog circuit is well-suited to perform positive A/D conversions. When
the R1 resistors are tied to ground for differential measurements, both differential inputs
must be referenced to analog ground, and both inputs must be positive with respect to
analog ground.
R0
LN0
AGND
LN1
ADC
BVREF
R0
C
R1
C
ADC
(RCM4100)
1
3
相關PDF資料
PDF描述
20-101-1197 MODULE RABBITCORE RCM3910 ROHS
20-101-1215 MCU RCM4050 RABBITCORE
20-101-1246 CORE MODULE RCM5400W
20-101-1260 BL5S220 SBC (RCM5400-BASED)
20-101-1319 MINCORE MODULE RCM6710
相關代理商/技術參數
參數描述
20-101-1170 功能描述:Zigbee/802.15.4模塊 RCM4510W CORE MODULE RoHS:否 制造商:Digi International 頻帶:902 MHz to 928 MHz 視線范圍: 數據速率: 靈敏度: 工作電源電壓:2.4 V to 3.6 V 傳輸供電電流:215 mA 接收供電電流:26 mA 輸出功率:250 mW 天線連接器類型:Wire 最大工作溫度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
20-101-1179 功能描述:模塊化系統 - SOM RCM3209 RABBITCORE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1183 功能描述:程序設計器配件 USB PROGRAM CABLE RoHS:否 制造商:Lattice 產品:ispDOWNLOAD Cables 用于:In-system Programming
20-101-1184 功能描述:模塊化系統 - SOM IC CPU RABBIT 2000 (2 pack) RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1185 功能描述:微處理器 - MPU IC CPU RABBIT 3000A (2 pack) RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324