2. GETTING STARTED This chapter describes" />
參數資料
型號: 20-101-1154
廠商: Rabbit Semiconductor
文件頁數: 13/112頁
文件大?。?/td> 0K
描述: MODULE RCM4120 RABBITCORE
標準包裝: 1
系列: RabbitCore®
模塊/板類型: MPU 核心模塊
適用于相關產品: RCM4120
其它名稱: 316-1122
User’s Manual
7
2. GETTING STARTED
This chapter describes the RCM4100 series in more detail, and
explains how to set up and use the accompanying Prototyping Board.
NOTE: This chapter (and this manual) assume that you have the RCM4100 Development
Kit. If you purchased an RCM4100 module by itself, you will have to adapt the infor-
mation in this chapter and elsewhere to your test and development setup.
2.1 Install Dynamic C
To develop and debug programs for the RCM4100 series (and for all other Rabbit hard-
ware), you must install and use Dynamic C.
If you have not yet installed Dynamic C version 10.01 (or a later version), do so now by
inserting the Dynamic C CD from the RCM4100 Development Kit in your PC’s CD-ROM
drive. If autorun is enabled, the CD installation will begin automatically.
If autorun is disabled or the installation does not start, use the Windows Start | Run menu
or Windows Disk Explorer to launch setup.exe from the root folder of the CD-ROM.
The installation program will guide you through the installation process. Most steps of the
process are self-explanatory.
Dynamic C uses a COM (serial) port to communicate with the target development system.
The installation allows you to choose the COM port that will be used. The default selec-
tion is COM1. You may select any available port for Dynamic C’s use. If you are not cer-
tain which port is available, select COM1. This selection can be changed later within
Dynamic C.
NOTE: The installation utility does not check the selected COM port in any way. Speci-
fying a port in use by another device (mouse, modem, etc.) may lead to a message such
as "could not open serial port" when Dynamic C is started.
Once your installation is complete, you will have up to three new icons on your PC desk-
top. One icon is for Dynamic C, one opens the documentation menu, and the third is for
the Rabbit Field Utility, a tool used to download precompiled software to a target system.
If you have purchased any of the optional Dynamic C modules, install them after installing
Dynamic C. The modules may be installed in any order. You must install the modules in
the same directory where Dynamic C was installed.
相關PDF資料
PDF描述
20-101-1197 MODULE RABBITCORE RCM3910 ROHS
20-101-1215 MCU RCM4050 RABBITCORE
20-101-1246 CORE MODULE RCM5400W
20-101-1260 BL5S220 SBC (RCM5400-BASED)
20-101-1319 MINCORE MODULE RCM6710
相關代理商/技術參數
參數描述
20-101-1170 功能描述:Zigbee/802.15.4模塊 RCM4510W CORE MODULE RoHS:否 制造商:Digi International 頻帶:902 MHz to 928 MHz 視線范圍: 數據速率: 靈敏度: 工作電源電壓:2.4 V to 3.6 V 傳輸供電電流:215 mA 接收供電電流:26 mA 輸出功率:250 mW 天線連接器類型:Wire 最大工作溫度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
20-101-1179 功能描述:模塊化系統 - SOM RCM3209 RABBITCORE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1183 功能描述:程序設計器配件 USB PROGRAM CABLE RoHS:否 制造商:Lattice 產品:ispDOWNLOAD Cables 用于:In-system Programming
20-101-1184 功能描述:模塊化系統 - SOM IC CPU RABBIT 2000 (2 pack) RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1185 功能描述:微處理器 - MPU IC CPU RABBIT 3000A (2 pack) RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324