參數資料
型號： 20-101-1105
廠商： Rabbit Semiconductor
文件頁數： 108/112頁
文件大小： 0K
描述： MODULE RCM4100 RABBITCORE
標準包裝： 1
系列： RabbitCore®
模塊/板類型： MPU 核心模塊
適用于相關產品： RCM4100
其它名稱： 316-1121
User’s Manual
91
Many other possible ranges are possible by physically changing the resistor values that
make up the attenuator circuit.
NOTE: Analog input LN7_IN does not have the 10 k
resistor installed, and so no
resistor attenuator is available, limiting its maximum input voltage to 2 V. This input is
intended to be used for a thermistor that you may install at header location JP25.
It is also possible to read a negative voltage on LN0_IN–LN5_IN by moving the 0
jumper (see Figure B-6) on header JP23 or JP24 associated with the A/D converter input
from analog ground to the reference voltage generated and buffered by the A/D converter.
Adjacent input channels are paired; moving the jumper on JP 23 changes both of the
paired channels (LN4_IN–LN5_IN), and moving the jumper on JP24 changes LN0_IN–
LN1_IN and LN2_IN–LN3_IN. At the present time Rabbit does not offer the software
drivers to work with single-ended negative voltages, but the differential mode described
below may be used to measure negative voltages.
Differential measurements require two channels. As the name differential implies, the dif-
ference in voltage between the two adjacent channels is measured rather than the differ-
ence between the input and analog ground. Voltage measurements taken in differential
mode have a resolution of 12 bits, with the 12th bit indicating whether the difference is
positive or negative.
The A/D converter chip can only accept positive voltages, as explained in Section 4.4. Both
differential inputs must be referenced to analog ground, and both inputs must be positive
with respect to analog ground. Table B-4 provides the differential voltage ranges for this
setup.
Table B-4. Differential Voltage Ranges
Min. Differential
Voltage
(V)
Max. Differential
Voltage (with
prescaler)
(V)
Gain
Multiplier
A/D Converter
Actual Gain
Resolution
(mV)
0
±22.528
×1
1
11
0±11.264
×2
1.8
5.5
0
±5.632
×4
3.6
2.75
0
±4.506
×5
4.5
2.20
0
±2.816
×8
7.2
1.375
0
±2.253
×10
9.0
1.100
0
±1.408
×16
14.4
0.688
0
±1.126
×20
18
0.550
相關PDF資料
PDF描述
20-101-1028 MODULE RABBITCORE RCM3750
046232104015800+ CONN FFC/FPC 4POS 1MM VERT SMD
20-101-0454 MODULE RABBITCORE RCM2200
20-101-0405 MODULE RABBITCORE RCM2010
20-101-1093 RCM4110 RABBITCORE
相關代理商/技術參數
參數描述
20-101-1110 功能描述:界面開發工具 Rio Protyping Board RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
20-101-1112 功能描述:模塊化系統 - SOM RCM4010 Core Module RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1114 功能描述:開發板和工具包 - 其他處理器 RCM4010 Kit RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓:
20-101-1131 功能描述:模塊化系統 - SOM RCM4200 RabbitCore- Module RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1132 功能描述:模塊化系統 - SOM RCM4210 RabbitCore- Module RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*