參數資料
型號： 20-101-1093
廠商： Rabbit Semiconductor
文件頁數： 50/112頁
文件大?。?/td> 0K
描述： RCM4110 RABBITCORE
標準包裝： 1
系列： RabbitCore®
模塊/板類型： MPU 核心模塊
適用于相關產品： RCM4110
產品目錄頁面： 619 (CN2011-ZH PDF)
其它名稱： 316-1140
38
RabbitCore RCM4100
4.4 A/D Converter (RCM4100 only)
The RCM4100 has an onboard ADS7870 A/D converter whose scaling and filtering are
done via the motherboard on which the RCM4100 module is mounted. The A/D converter
multiplexes converted signals from eight single-ended or four differential inputs to Serial
Port B on the Rabbit 4000.
The eight analog input pins, LN0–LN7, each have an input impedance of 6–7 M
,
depending on whether they are used as single-ended or differential inputs. The input signal
can range from -2 V to +2 V (differential mode) or from 0 V to +2 V (single-ended mode).
Use a resistor divider such as the one shown in Figure 9 to measure voltages above 2 V on
the analog inputs. See Appendix B.4.3 for information on how to measure negative voltages.
Figure 9. Resistor Divider Network for Analog Inputs
The R1 resistors are typically 20 k
to 100 k, with a lower resistance leading to more
accuracy, but at the expense of a higher current draw. The R0 resistors would then be
180 k
to 900 k for a 10:1 attenuator. The capacitor filters noise pulses on the A/D
converter input.
The actual voltage range for a signal going to the A/D converter input is also affected by
the 1, 2, 4, 5, 8, 10, 16, and 20 V/V software-programmable gains available on each channel
of the ADS7870 A/D converter. Thus, you must scale the analog signal with an attenuator
circuit and a software-programmable gain so that the actual input presented to the A/D
converter is within the range limits of the ADS7870 A/D converter chip (-2 V to + 2 V or
0 V to + 2 V).
The A/D converter chip can only accept positive voltages. With the R1 resistors connected
to ground, your analog circuit is well-suited to perform positive A/D conversions. When
the R1 resistors are tied to ground for differential measurements, both differential inputs
must be referenced to analog ground, and both inputs must be positive with respect to
analog ground.
R0
LN0
AGND
LN1
ADC
BVREF
R0
C
R1
C
ADC
(RCM4100)
1
3
相關PDF資料
PDF描述
20-101-0453 MODULE RABBITCORE RCM2300
20-101-1235 CORE MODULE RCM5700
11FMN-BMTTR-A-TB CONN FMN HSNG 11POS STAG REV SMD
046232103103800+ CONN FFC/FPC 3POS 1MM R/A SMD
15FE-ST-VK-N CONN FFC 15POS RA 1.25MM
相關代理商/技術參數
參數描述
20-101-1094 功能描述:模塊化系統 - SOM RCM4000 Coremodule RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1095 功能描述:模塊化系統 - SOM BL2600 XD HOT SWAP 10/100 RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1104 功能描述:處理器配件 USB xd reader RoHS:否 制造商:Olimex Ltd. 產品:Cable 用于:
20-101-1105 功能描述:模塊化系統 - SOM RCM4100 RabbitCore Module RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1110 功能描述:界面開發工具 Rio Protyping Board RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*