參數資料
型號： 20-101-1093
廠商： Rabbit Semiconductor
文件頁數： 106/112頁
文件大小： 0K
描述： RCM4110 RABBITCORE
標準包裝： 1
系列： RabbitCore®
模塊/板類型： MPU 核心模塊
適用于相關產品： RCM4110
產品目錄頁面： 619 (CN2011-ZH PDF)
其它名稱： 316-1140
User’s Manual
89
B.4.1 Adding Other Components
There are pads for 28-pin TSSOP devices, 16-pin SOIC devices, and 6-pin SOT devices
that can be used for surface-mount prototyping with these devices. There are also pads that
can be used for SMT resistors and capacitors in an 0805 SMT package. Each component
has every one of its pin pads connected to a hole in which a 30 AWG wire can be soldered
(standard wire wrap wire can be soldered in for point-to-point wiring on the Prototyping
Board). Because the traces are very thin, carefully determine which set of holes is con-
nected to which surface-mount pad.
B.4.2 Measuring Current Draw
The Prototyping Board has a current-measurement feature available at header locations
JP1 and JP2 for the +5 V and +3.3 V supplies respectively. To measure current, you will
have to cut the trace on the bottom side of the Prototyping Board corresponding to the
power supply or power supplies whose current draw you will be measuring. Header loca-
tions JP1 and JP2 are shown in Figure B-5. Then install a 1 × 2 header strip from the
Development Kit on the top side of the Prototyping Board at the header location(s) whose
trace(s) you cut. The header strip(s) will allow you to use an ammeter across their pins to
measure the current drawn from that supply. Once you are done measuring the current,
place a jumper across the header pins to resume normal operation.
Figure B-5. Prototyping Board Current-Measurement Option
NOTE: Once you have cut the trace below header location JP1 or JP2, you must either be
using the ammeter or have a jumper in place in order for power to be delivered to the
Prototyping Board.
A
0
Cut traces
Bottom Side
JP1
JP2
JP1 (+5 V)
or
JP2 (+3.3 V)
CURRENT
MEASUREMENT
D1
R1
PWR
DS1
GND
J1
U1
C1
GND
C2
JP1
C3
D2
JP2
L1C6
C5
JP1
JP2
相關PDF資料
PDF描述
20-101-0453 MODULE RABBITCORE RCM2300
20-101-1235 CORE MODULE RCM5700
11FMN-BMTTR-A-TB CONN FMN HSNG 11POS STAG REV SMD
046232103103800+ CONN FFC/FPC 3POS 1MM R/A SMD
15FE-ST-VK-N CONN FFC 15POS RA 1.25MM
相關代理商/技術參數
參數描述
20-101-1094 功能描述:模塊化系統 - SOM RCM4000 Coremodule RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1095 功能描述:模塊化系統 - SOM BL2600 XD HOT SWAP 10/100 RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1104 功能描述:處理器配件 USB xd reader RoHS:否 制造商:Olimex Ltd. 產品:Cable 用于:
20-101-1105 功能描述:模塊化系統 - SOM RCM4100 RabbitCore Module RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1110 功能描述:界面開發工具 Rio Protyping Board RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*