參數資料
型號: 101-0478
廠商: Rabbit Semiconductor
文件頁數: 77/90頁
文件大?。?/td> 0K
描述: KIT DEV RABBIT RCM2200 INTL
標準包裝: 1
系列: RabbitCore 2000
類型: MPU 模塊
適用于相關產品: RCM2200
所含物品: RabbitCore 模塊,開發板,纜線和 Dynamic C? CD-Rom
User’s Manual
73
C.2 Chip Select Circuit
The RCM2200 has provision for battery backup, which kicks in to keep VRAM from
dropping below 2 V.
When the RCM2200 is not powered, the battery keeps the SRAM memory contents and
the real-time clock (RTC) going. The SRAM has a powerdown mode that greatly reduces
power consumption. This powerdown mode is activated by raising the chip select (CS)
signal line. Normally the SRAM requires Vcc to operate. However, only 2 V is required
for data retention in powerdown mode. Thus, when power is removed from the circuit, the
battery voltage needs to be provided to both the SRAM power pin and to the CS signal
line. The CS control switch accomplishes this task for the CS signal line.
Figure C-3 shows a schematic of the chip select control switch.
Figure C-3. Chip Select Control Switch
In a powered-up condition, the CS control switch must allow the processor’s chip select
signal /CS1 to control the SRAM’s CS signal /CSRAM. So, with power applied, /CSRAM
must be the same signal as /CS1, and with power removed, /CSRAM must be held high
(but only needs to be as high as the battery voltage). Q3 and Q4 are MOSFET transistors
with opposing polarity. They are both turned on when power is applied to the circuit. They
allow the CS signal to pass from the processor to the SRAM so that the processor can peri-
odically access the SRAM. When power is removed from the circuit, the transistors will
turn off and isolate /CSRAM from the processor. The isolated /CSRAM line has a 100 k
pullup resistor to VRAM (R28). This pullup resistor keeps /CSRAM at the VRAM voltage
level (which under no power condition is the backup battery’s regulated voltage at a little
more than 2 V).
Transistors Q3 and Q4 are of opposite polarity so that a rail-to-rail voltages can be passed.
When the /CS1 voltage is low, Q3 will conduct. When the /CS1 voltage is high, Q4 will
conduct. It takes time for the transistors to turn on, creating a propagation delay. This
delay is typically very small, about 10 ns to 15 ns.
/CS1
/CSRAM
/RESET_OUT
Q3
Q4
R28
VRAM
100 kW
VRAM
SWITCH
相關PDF資料
PDF描述
RBC20DRXH CONN EDGECARD 40POS DIP .100 SLD
N001-005-BK-R CABLE PATCH CAT5E BLACK 5'
SDR-BK SCOTCH CODE REFILL BLACK
94SVPD186X0035F8 CAP ALUM 18UF 35V 20% SMD
GCC18DCMT-S288 CONN EDGECARD 36POS .100 EXTEND
相關代理商/技術參數
參數描述
101048 制造商:Jacob 功能描述:Bulk
10-1-048 制造商:IGUS 功能描述:SERIES 10 ENERGY CHAIN
101-0480 功能描述:開發板和工具包 - 其他處理器 RCM2300 DEV KIT RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓:
101-048-033 制造商:PANCON CONNECTORS 功能描述:Conn Shrouded Header HDR 48 POS 5.08mm Solder RA Thru-Hole 制造商:ITW Pancon 功能描述:Conn Shrouded Header HDR 48 POS 5.08mm Solder RA Thru-Hole
101-0481 功能描述:KIT DEV RABBIT RCM2300 INTL RoHS:否 類別:編程器,開發系統 >> 通用嵌入式開發板和套件(MCU、DSP、FPGA、CPLD等) 系列:RabbitCore 2000 產品培訓模塊:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色產品:Blackfin? BF50x Series Processors 標準包裝:1 系列:Blackfin® 類型:DSP 適用于相關產品:ADSP-BF548 所含物品:板,軟件,4x4 鍵盤,光學撥輪,QVGA 觸摸屏 LCD 和 40G 硬盤 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相關產品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA