參數資料
型號: 101-0478
廠商: Rabbit Semiconductor
文件頁數: 19/90頁
文件大?。?/td> 0K
描述: KIT DEV RABBIT RCM2200 INTL
標準包裝: 1
系列: RabbitCore 2000
類型: MPU 模塊
適用于相關產品: RCM2200
所含物品: RabbitCore 模塊,開發板,纜線和 Dynamic C? CD-Rom
20
RabbitCore RCM2200
The RCM2200 has 26 parallel I/O lines grouped in five 8-bit ports available on headers J4
and J5. The 16 bidirectional I/O lines are located on pins PA0–PA7, PD3–PD5, and PE0–
PE1, PE4, PE5, and PE7. The pinouts for headers J4 and J5 are shown in Figure 5.
Figure 5. RCM2200 I/O Pinouts
4.1.1 Dedicated Inputs
PB0 is a general CMOS input when the Rabbit 2000 is either not using Serial Port B or is
using Serial Port B in an asynchronous mode. Four other general CMOS input-only pins
are located on PB2–PB5. These pins can also be used for the slave port. PB2 and PB3 are
slave write and slave read strobes, while PB4 and PB5 serve as slave address lines SA0
and SA1, and are used to access the slave registers. PC1 and PC3 are general CMOS inputs
only. These pins can instead be selectively enabled to serve as the serial data inputs for
Serial Ports D and C.
4.1.2 Dedicated Outputs
One of the general CMOS output-only pins is located on PB7. PB7 can also be used with
the slave port as the /SLAVEATTN output. This configuration signifies that the slave is
requesting attention from the master. PC0 and PC2 are also output-only pins; PC0 and
PC2 can instead serve as the serial data outputs for Serial Ports D and C.
4.1.3 Memory I/O Interface
Four of the Rabbit 2000 address lines (A0–A3) and all the data lines (D0–D7) are available.
I/0 write (/IOWR) and I/0 read (/IORD) are also available for interfacing to external devices.
The ports on the Rabbit 2000 microprocessor used in the RCM2200 are configurable, and
so the factory defaults can be reconfigured. Table 1 lists the Rabbit 2000 factory defaults
and the alternate configurations.
Note: These pinouts are as seen on
the Bottom Side of the module.
VCC
PC1
PC3
TPOUT+
PD3
PD5
/IOWR
PE1
TPIN+
PE5
PE7
A2
A0
GND
PC0
PC2
TPOUT-
LNK
PD4
/IORD
PE0
TPIN-
PE4
ACT
A3
A1
J4
PA0
PA2
PA4
PA6
/RES
PB2
PB4
PB7
D6
D4
D2
D0
VCC
PA1
PA3
PA5
PA7
PB0
PB3
PB5
D7
D5
D3
D1
VBAT
GND
J5
相關PDF資料
PDF描述
RBC20DRXH CONN EDGECARD 40POS DIP .100 SLD
N001-005-BK-R CABLE PATCH CAT5E BLACK 5'
SDR-BK SCOTCH CODE REFILL BLACK
94SVPD186X0035F8 CAP ALUM 18UF 35V 20% SMD
GCC18DCMT-S288 CONN EDGECARD 36POS .100 EXTEND
相關代理商/技術參數
參數描述
101048 制造商:Jacob 功能描述:Bulk
10-1-048 制造商:IGUS 功能描述:SERIES 10 ENERGY CHAIN
101-0480 功能描述:開發板和工具包 - 其他處理器 RCM2300 DEV KIT RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓:
101-048-033 制造商:PANCON CONNECTORS 功能描述:Conn Shrouded Header HDR 48 POS 5.08mm Solder RA Thru-Hole 制造商:ITW Pancon 功能描述:Conn Shrouded Header HDR 48 POS 5.08mm Solder RA Thru-Hole
101-0481 功能描述:KIT DEV RABBIT RCM2300 INTL RoHS:否 類別:編程器,開發系統 >> 通用嵌入式開發板和套件(MCU、DSP、FPGA、CPLD等) 系列:RabbitCore 2000 產品培訓模塊:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色產品:Blackfin? BF50x Series Processors 標準包裝:1 系列:Blackfin® 類型:DSP 適用于相關產品:ADSP-BF548 所含物品:板,軟件,4x4 鍵盤,光學撥輪,QVGA 觸摸屏 LCD 和 40G 硬盤 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相關產品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA