- 您現在的位置：買賣IC網 > PDF目錄3908 > 101-0411 (Rabbit Semiconductor)INTERFACE 12KEYDISP ETHNT OP6700 PDF資料下載
參數資料
| 型號： | 101-0411 |
| 廠商： | Rabbit Semiconductor |
| 文件頁數： | 24/90頁 |
| 文件大小： | 0K |
| 描述： | INTERFACE 12KEYDISP ETHNT OP6700 |
| 標準包裝： | 25 |
| 系列： | SBC |
| 模塊/板類型： | 單板計算機模塊 |
| 適用于相關產品： | OP6700 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁
26
Intellicom (OP6600/OP6700)
3.2.3 Programming Port
The Intellicom has a 10-pin programming header labeled J4. The programming port uses
the Rabbit 2000’s serial port A for communication. The programming port uses the Rabbit
2000’s Serial Port A for communication. Dynamic C uses the programming port to down-
load and debug programs.
The programming port is also used for the following operations.
Cold-boot the Rabbit 2000 on the Intellicom after a reset.
Remotely download and debug a program over an Ethernet connection using the
RabbitLink EG2110.
Fast copy designated portions of flash memory from one Rabbit-based board (the
master) to another (the slave) using the Rabbit Cloning Board.
Alternate Uses of the Programming Port
All three clocked Serial Port A signals are available as
a synchronous serial port
an asynchronous serial port, with the clock line usable as a general CMOS input
The programming port may also be used as a serial port via the DIAG connector on the
programming cable.
In addition to Serial Port A, the Rabbit 2000 startup-mode (SMODE0, SMODE1), status,
and reset pins are available on the programming port header.
The two startup mode pins determine what happens after a reset—the Rabbit 2000 is
either cold-booted or the program begins executing at address 0x0000.
The status pin is used by Dynamic C to determine whether a Rabbit microprocessor is
present. The status output has three different programmable functions:
1. It can be driven low on the first op code fetch cycle.
2. It can be driven low during an interrupt acknowledge cycle.
3. It can also serve as a general-purpose output.
The /RESET_IN pin is an external input that is used to reset the Rabbit 2000 and the Intel-
licom onboard peripheral circuits.
Refer to the Rabbit 2000 Microprocessor User’s Manual for more information.
相關PDF資料 |
PDF描述 |
|---|---|
| AT24C02A-10PI-2.7 | IC EEPROM 2KBIT 400KHZ 8DIP |
| AT24C02A-10PI-1.8 | IC EEPROM 2KBIT 400KHZ 8DIP |
| 25FMN-BMT-A-TF | CONN FMN HSNG 25POS SNGL NOR SMD |
| 046239012001800+ | CONN FPC ONE-TOUCH LCK .5MM 12 |
| AT24C01-10PI-1.8 | IC EEPROM 1KBIT 400KHZ 8DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 10104110 | 制造商:FCI-CONNECTOR 制造商全稱:FCI connector 功能描述:MICRO USB B TYPE RECEPTACLE |
| 10104110-0001LF | 功能描述:USB接頭 5P Quick Connect Micro USB TypeB Rcpt RoHS:否 制造商:FCI 產品:USB Type A Connectors 標準:USB 3.0 端口數量: 位置/觸點數量:9 型式:Female 電流額定值:1.8 A 安裝風格:Through Hole 端接類型:Solder Pin 連接器類型:USB 3.0 Receptacle |
| 10104110-0001LF | 制造商:FCI 功能描述:MICRO USB B, RECEPTACLE, 5POS, SMT RT AN |
| 10-104-11-01 | 制造商:Concord Electronics Inc 功能描述:Contact Solder ST Thru-Hole |
| 10-104-11-03 | 制造商:Concord Electronics Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。