- 您現在的位置：買賣IC網 > PDF目錄24623 > 051-911-9072 (ITT Corporation) RF Coaxial Connectors PDF資料下載
參數資料
| 型號： | 051-911-9072 |
| 廠商： | ITT Corporation |
| 英文描述： | RF Coaxial Connectors |
| 中文描述： | 射頻同軸連接器 |
| 文件頁數： | 9/42頁 |
| 文件大?。?/td> | 489K |
| 代理商： | 051-911-9072 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
Dimensions are shown in mm (inch)
Dimensions subject to change
118
RF Coaxial Connectors
Assembly Instructions
AI-302
SMA Straight Connectors, Direct Solder (Cable Conductor used as Center Contact) Type for Semi-Rigid Cable
1. Trim the cable outer conductor and dielectric as shown taking care not to nick the center conductor
using Tool T2624, if available, or other cable cutting tool. Deburr outer conductor at point of cut.
‘A’ = 2,16
± 0,13 (.085 ± .005)
2. Point the end of the center conductor using Tool T2297 if available or a miniature file.
3. If style - 9073 is being assembled slip the coupling nut onto the cable.
4. Clean housing area of outer conductor with abrasive paper and clean in a suitable agent. Place 24
s.w.g. soldering ring and connector body on prepared end of cable. Ensure body is correct way
round. End of cable to be flush with end of connector body as shown.
Using Assembly Jig T1848, or other suitable clamping arrangement, clamp in a vertical position.
Heat the connector body using an appropriate heat source (solder tongs with variable control).
Apply sufficient heat for solder to flow but using minimum heat cycle.
5. Compress expanded dielectric back into cable outer conductor with Dielectric Compression Tool
as shown, until it is flush with end of body and outer conductor.
6. Fit the interface seal.
7. Install the spring retaining ring, compress with tool T0557/1 and fit the coupling nut.
BODY
RETAINING
RING
INTERFACE
SEAL
COUPLING
NUT
DIELECTRIC
COMPRESSION TOOL
相關PDF資料 |
PDF描述 |
|---|---|
| 9248YF-112-T | PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| 9248YF-185LFT | 133.33 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO28 |
| 9248YF-195LF-T | 140 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| 051-923-9188 | RF Coaxial Connectors |
| 9248YF-20LF | PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 05-1912 | 制造商:ITW Pancon 功能描述: |
| 05-1913 | 制造商:ITW Pancon 功能描述: |
| 0-519151-9 | 制造商:MACOM 制造商全稱:Tyco Electronics 功能描述:ERGOCRIMP Die Set for Type XII and Type III |
| 051-923-9188 | 制造商:ITT 制造商全稱:ITT Industries 功能描述:RF Coaxial Connectors |
| 051-928-9019 | 制造商:ITT 制造商全稱:ITT Industries 功能描述:RF Coaxial Connectors |
發布緊急采購，3分鐘左右您將得到回復。