- 您現在的位置：買賣IC網 > PDF目錄382791 > μPD78P064 (NEC Corp.) 8 Bit Single Chip Microcontrollers PDF資料下載
參數資料
| 型號： | μPD78P064 |
| 廠商： | NEC Corp. |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8 Bit Single Chip Microcontrollers |
| 中文描述： | 8位單片機微控制器 |
| 文件頁數： | 23/70頁 |
| 文件大?。?/td> | 473K |
| 代理商： | ΜPD78P064 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
23
m
PD78P064
(1)
Read mode
Read mode is set if CE = L, OE = L is set.
(2)
Output disable mode
Data output becomes high-impedance, and is in the output disable mode, of OE = H is set.
Therefore, it allows data to be read from any device by controlling the OE pin, if multiple
m
PD78P064s are connected
to the data bus.
(3)
Standby mode
Standby mode is set if CE = H is set.
In this mode, data outputs become high-impedance irrespective of the OE status.
(4)
Page data latch mode
Page data latch mode is set if CE = H, PGM = H, OE = L are set at the beginning of page write mode.
In this mode, 1 page 4-byte data is latched in an internal address/data latch circuit.
(5)
Page write mode
After 1 page 4 bytes of addresses and data are latched in the page data latch mode, a page write is executed by applying
a 0.1 ms program pulse (active low) to the PGM pin with CE = H, OE = H. Then, program verification can be performed,
if CE = L, OE = L are set.
If programming is not performed by a one-time program pulse, X (X
￡
10) write and verification operations should be
executed repeatedly.
(6)
Byte write mode
Byte write is executed when a 0.1 ms program pulse (active low) is applied to the PGM pin with CE = L, OE = H. Then,
program verification can be performed if OE = L is set.
If programming is not performed by a one-time program pulse, X (X
￡
10) write and verification operations should be
executed repeatedly.
(7)
Program verify mode
Program verify mode is set if CE = L, PGM = H, OE = L are set. In this mode, check if a write operation is performed
correctly, after the write.
(8)
Program inhibit mode
Program inhibit mode is used when the OE pin, V
PP
pin and D0 to D7 pins of multiple
m
PD78P064s are connected in
parallel and a write is performed to one of those devices.
When a write operation is performed, the page write mode or byte write mode described above is used. At this time,
a write is not performed to a device which has the PGM pin driven high.
相關PDF資料 |
PDF描述 |
|---|---|
| μPD78P078Y | 8 Bit Single Chip Microcontrollers(8位單片微控制器) |
| μPD78P081(A2) | 8 Bit Single Chip Microcontrollers(8位單片微控制器) |
| μPD78081 | 8 Bit Single Chip Microcontrollers(8位單片微控制器) |
| μPD78083(A) | 8 Bit Single Chip Microcontrollers(8位單片微控制器) |
| μPD78P083 | 8 Bit Single Chip Microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PD7935 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:FOR OPTICAL COMMUNICATION |
| PD7937 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:InGaAs PIN PHOTO DIODES |
| PD793D26 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:InGaAs PIN PHOTO DIODES |
| PD793D7 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:InGaAs PIN PHOTO DIODES |
| PD79920-0M | 制造商:Citizen Systems America Corporation 功能描述:Mobile Printer - PD24 USB Cable |
發布緊急采購，3分鐘左右您將得到回復。